Specifications; Standard Accessories; Prior To Operation - Hitachi d 10vf Bedienungsanleitung

English

SPECIFICATIONS

Model
Voltage (by areas)*
Power input
No load speed
Drill chuck capacity
Steel
Capacity
Wood
Weight (without cord)
Spec. for keyed chuck
Spec. for keyless chuck
*Be sure to check the nameplate on product as it is subject to change by areas.
<Capacity with Angle attachment (Optional accessory for D13VF and D13VG)>
Model
Speed of angle unit
Steel
Capacity
Wood

STANDARD ACCESSORIES

<D10VF>
(1) Chuck wrench (Spec. only for keyed chuck) ...... 1
<D10VG and D13VF>
(1) Side handle ................................................................ 1
(2)Chuck wrench (Spec. only for keyed chuck) ........ 1
<D13VG>
(1) Side handle ................................................................ 1
(2) Handle joint ................................................................ 1
(3) Chuck wrench (Spec. only for keyed chuck) ...... 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
<D10VF>
(1) Side handle
(2) Hook (A)
<D10VG>
(1) Hook (A)
<D13VF and D13VG>
(1) Hook (A)
(2) Angle attachment
Optional accessories are subject to change without notice.
APPLICATIONS
Boring holes in metal, wood and plastic.
5
D10VF
0–3,000min
Twist Bit 10 mm
Hole Saw
Flat Spade Bit 25 mm
Auger Bit
Hole Saw 29 mm
1.8 kg
1.8 kg
LOW(650min
Twist Bit 13 mm
Hole Saw 64 mm
Flat Spade Bit 40 mm
Auger Bit 38 mm
Hole Saw 114 mm
D10VG
(110V, 220V, 230V, 240V)
710W*
–1 0–1,200min –1
10 mm
10 mm
– 38 mm
32 mm
– –
70 mm
1.9 kg
1.9 kg
D13VF
–1 ) HIGH(1350min –1
13 mm
32 mm
32 mm
29 mm
64 mm

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, inviting serious
accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Selecting the appropriate drill bit:
When boring metal or plastic
Use ordinary metalworking drill bits.
When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes,
use a metalworking drill bit.
5. Mounting and dismounting of the bit
For keyed chuck (Fig. 1)
(1) Open the chuck jaws, and insert the bit into the
chuck.
(2) Place the chuck wrench in each of the three holes
in the chuck, and turn it in the clockwise direction
(viewed from the front side). Tighten securely.
D13VF D13VG
0–850min –1 0–600min
13 mm
13 mm 13 mm
51 mm 70 mm
40 mm 40 mm
32 mm 38 mm
102 mm 114 mm
2.1 kg 2.1 kg
2.0 kg 2.0 kg
D13VG
) LOW(400min –1 ) HIGH(900min
13 mm 13 mm
70 mm 51 mm
40 mm 40 mm
38 mm 32 mm
114 mm 102 mm
–1
–1 )