Advice Regarding The First Wash Cycle; Electrical Connection; Technical Data; Ecodesign Regulation - Scholtes LPE 14-H070 Bedienungsanleitung

Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Some models are also equipped with the supplementary safety
*
device New Acqua Stop , which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut as it
contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make sure
that:
• The socket is earthed and complies with current regulations.
• The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located on the
inside of the door ( see chapter entitled Description of the
appliance ).
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance. If this
is not the case, ask an authorised technician to replace the
plug ( see Assistance ); do not use extension cables or
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal
soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even
further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 4,5 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
Standard conditions
Energy consumption
(kWh/cycle)
INTENSIVE 1,50
NORMAL
1,20
*
Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
**
Data is obtained by recording values when the appliance is operational and loaded with user crockery.
*
Water consumption Duration
(l/cycle) (min/cycle)
15 150
15 120
*
Anti-condensation strip
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt ( see
chapter entitled Rinse aid and refined salt ). The water may
overflow: this is normal and is not a cause for concern. Select
the water hardness value ( see chapter entitled Rinse aid and
refined salt ). - After the salt has been poured into the
machine, the LOW SALT indicator light
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.

Technical data

width 59.5 cm
Dimensions height 82 cm
depth 57 cm
Capacity 14 standard place-settings
Water supply 0,05 ÷ 1MPa (0.5 ÷ 10 bar)
pressure 7,25 – 145 psi
Power supply
See appliance data plate
voltage
Total absorbed
See appliance data plate
power
Fuse See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Labelling)
-2002/96/EC (WEEE)
**
User conditions
Energy consumption Water consumption
(kWh/cycle) (l/cycle)
1,30 14
1,05 14
EN
*
switches off.
Duration
(min/cycle)
135
110
15