Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Resetting Wi-Fi
Take the following steps if the robot vacuum cannot be connected to the network because the
router is reset, the password is forgotten, or for other reasons:
1. Open the cover of the robot vacuum so that you can see the Wi-Fi indicator.
2. Simultaneously press and hold the buttons
and
for 7 seconds until you hear a voice
prompt to indicate that the robot vacuum is waiting for the network configuration.
3. When the Wi-Fi indicator blinks, the Wi-Fi connection has been reset successfully.
Turning On/Off
· Press and hold the button
for three seconds to turn the robot vacuum on. When the
indicator on the robot vacuum lights up, it means the robot vacuum enters the standby mode.
· When the robot vacuum is paused and not being charged, press and hold the button
three seconds to turn it off.
Note: When the robot vacuum is charging, it will automatically turn on and cannot be turned off.
Quick Map Creation
· After configuring the network for the first time, follow the instructions in the app to quickly
create a map, and the robot vacuum will start mapping without cleaning.
· The mapping process will be completed when the robot vacuum returns to the omni station,
and the map will be saved automatically.
Notes:
· Make sure the robot vacuum is fully charged and starts from the omni station.
· Before mapping, remove the items on the floor, open the doors of the rooms, and block the
areas unsuitable for the robot vacuum to enter.
· During mapping, do not follow, move, or interrupt the robot vacuum, and do not move the omni
station.
· After mapping, set up virtual walls or restricted areas in areas unsuitable for the robot vacuum to
enter, such as the areas where it may get stuck or be scraped.
· Set up virtual walls or restricted areas in areas with long-hair or fringe carpets to prevent the
robot vacuum from getting entangled.
· Set up virtual walls or restricted areas to exclude carpeted areas before mopping to prevent
the carpet from getting wet.
Pausing
When the robot vacuum is running, press any button to pause it.
Note: Do not lift or move the robot vacuum while it is paused. Otherwise, it may have positioning
errors that could prevent the robot vacuum from returning to the omni station or cause the loss
of the map.
08
Sleep Mode
The robot vacuum will automatically enter sleep mode after it is paused for 10 minutes, and its
indicator will go out. To wake it up, press any button on the robot vacuum.
Note: The robot vacuum will automatically turn off after being in sleep mode for 12 hours.
Resuming Cleanup
If the robot vacuum starts running low on battery during a cleaning task, it will automatically
return to the omni station to charge. When the robot vacuum is appropriately charged, it will
for
resume cleanup where it left off.
Child Lock Settings
To enable or disable the child lock, press and hold the button
on the robot vacuum for
three seconds.
Note: When the child lock function is enabled, the buttons on the robot vacuum will not work.
Instead, you can control the robot vacuum via the app.
Dust Emptying
When the robot vacuum automatically returns to the omni station to charge after completing a
vacuuming and mopping task, a vacuuming before mopping task, or a vacuuming task, the
omni station will automatically start to empty the dust compartment.
Notes:
· When the robot vacuum returns midway to the omni station to clean mop pads, the station
will not automatically empty the dust compartment.
· If the function of auto dust emptying is disabled in the app, the omni station will not
automatically empty the dust compartment.
· If you change the auto-empty frequency in the app, the omni station will empty dust at the
set frequency.
Vacuuming and Mopping
Start cleaning
· Before starting, ensure the mop assembly and other
necessary parts have been installed onto the robot
vacuum and the clean water tank has been added water.
· Select the vacuuming and mopping mode in the app,
and use the app or press the button
on the robot
vacuum to make it start from the station. Then the robot
vacuum will plan the optimal cleaning route and perform
the cleaning task based on the created map.
Notes:
· The robot vacuum will moisten the mop pads before starting, please wait with patience.
.
Before starting, ensure the omni station is connected to power and the robot vacuum is
connected to the omni station.
· To ensure that the robot vacuum can return to the omni station successfully after completing
vacuuming and mopping, it is recommended to make the robot vacuum start from the omni
station. Do not move the omni station, the clean water tank, the dirty water tank, or the
washboard during cleaning.
Automatically return to clean mop pads midway
During cleaning, the robot vacuum may automatically return to
the omni station to wash the mop pads after it cleans certain
squares of area. Once the mop pads have been washed, the
robot vacuum will resume its cleaning task.
Auto dust emptying & mop pad cleaning and air-drying
When the robot vacuum has completed its cleaning task
and returned to the omni station to charge, the omni
station will automatically start emptying dust and then
clean and air-dry the mop pads.
Clean the dirty water tank
After the mop pads have been cleaned and air-dried,
please clean the dirty water tank in time to prevent odors.
Vacuuming
Select the vacuuming mode in the app, then use the app or press the button
on the robot
vacuum to start cleaning, and the robot vacuum will lift the mop assembly and start from the
omni station to vacuum. Once it finishes vacuuming, it will return to the omni station to
automatically empty the dust compartment.
Notes: lf the mop assembly is not installed, the robot vacuum will automatically perform the
vacuuming after starting.
Mopping
Before starting, ensure the mop assembly and other necessary parts have been installed
onto the robot vacuum and the clean water tank has been added water. Select the mopping
mode in the app, and use the app or press the button
on the robot vacuum to start
cleaning. Then the robot vacuum will automatically moisten the mop pads first and leave the
omni station to start mopping. Once it finishes mopping, it will return to the omni station to
wash and air-dry the mop pads.
Vacuuming before Mopping
Before starting, ensure the mop assembly has been installed onto the robot vacuum and the
clean water tank has been added water. Select the vacuuming before mopping mode in the
app, and use the app or press the button
on the robot vacuum to start the cleaning task,
then the robot vacuum will lift the mop assembly to vacuum. Once it finishes vacuuming, it
will return to the omni station to automatically empty the dust and moisten the mop pads,
then it will lower the mop assembly to start mopping.
09
Werbung
