Herunterladen Inhalt Inhalt Diese Seite drucken

Troubleshooting - Hotpoint Ariston CAWD 129 Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für CAWD 129:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 43

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see "Assistance"), make
sure that the problem cannot be not solved easily using the following list.
Problem:
The washer-dryer does not
switch on.
The wash cycle does not start.
The washer-dryer does not take
in water (the indicator light for
the first wash cycle stage
flashes rapidly).
The washer-dryer continuously
takes in and drains water.
The washer-dryer does not drain
or spin.
The washer-dryer vibrates a lot
during the spin cycle.
The washer-dryer leaks.
The START/PAUSE indicator light
(orange) and the function
indicator lights flash rapidly.
There is too much foam.
The washer-dryer does not dry.
Possible causes / Solutions:
• The appliance is not plugged into the socket fully, or is not making contact.
• There is no power in the house.
• The washer-dryer door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A delayed start has been set (see "Personalisation").
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
• The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see "Installation").
• The free end of the hose is under water (see "Installation").
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the
dwelling is on one of the upper floors of a building, there may be problems
relating to water drainage, causing the washer-dryer to fill with water and
drain continuously. Special anti-draining valves are available in shops and
help to avoid this inconvenience.
• The wash cycle does not include draining: some wash cycles require
the drain phase to be started manually.
• The ANTI-CREASE function has been activated: To complete the wash
cycle, press the START/PAUSE button ("Personalisation").
• The drain hose is bent (see "Installation").
• The drainage duct is clogged.
• The drum was not unlocked correctly during installation (see "Installation").
• The washer-dryer is not level (see "Installation").
• The washer-dryer is trapped between cabinets and walls (see "Installation").
• The water inlet hose is not screwed on properly (see "Installation").
• The detergent dispenser drawer is blocked (for cleaning instructions, see
"Care and maintenance").
• The drain hose is not fixed properly (see "Installation").
• Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• The detergent is not suitable for machine washing (it should display the
text "for washer-dryers" or "hand and machine wash", or the like).
• Too much detergent was used.
• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
• The appliance door is not shut properly.
• A delayed start has been set.
• The DRYING knob is on the
setting.
GB
27

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis