Herunterladen Diese Seite drucken

Using The Device; End Of Operation; Maintenance; Emptying The Dust Collector - Clatronic BS 1307 A Bedienungsanleitung

Akku-bodenstaubsauger

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 4

Using the Device

You can use the appliance as a floor vacuum cleaner or as a
handheld and upright vacuum cleaner (basic unit).
1. Disconnect the appliance from the mains when changing
the accessory.
2. Turn on the device.
3. Select a power level.
NOTE:
We recommend the higher power level for using the
appliance with the floor nozzle.

End of Operation

1. Turn off the device.
2. If you have already installed the wall holder, hang up the
vacuum cleaner. You can attach the crevice / brush nozzle
and the upholstery nozzle at the left and the right of the
vacuum cleaner.

Maintenance

Emptying the Dust Collector

1. Disconnect the appliance from the power supply unit.
2. If necessary, remove the suction tube or the nozzle
attachment from the appliance.
3. Hold the appliance with the bottom plate of the dust
collector over a dustbin.
4. Empty the contents of the dust
collector. Slide the opener of
the dust collector downwards to
open the bottom plate.
5. Then close the base plate
again. The lock on the dust
collector must engage.

The Filter System

Your appliance features 3 filters. The common dust bag
system has been replaced by a transparent dust collector.
The higher flow speed of the collector allows for heavy dirt
and smallest floating particles to be separated from the
"sucked-in air".
It is thus not necessary to buy dust bags.
The filters must be cleaned periodically.
CAUTION:
• Never wash the filter in the washing machine.
• Do not use a hairdryer for drying.
• Only put the appliance back into operation when all fil-
ters are completely dry and correctly assembled.
44
BS1307A_IM
The Filter Unit
The filter unit is composed of:
• HEPA filter
• Coarse filter
Proceed as follows to clean
the filter unit:
1. Empty the dust container as described above. (Steps 1 - 5)
2. Disassembly of the filter unit
2.1 Press the dotted area of the button (1) to disconnect
the dust container from the motor housing.
2.2 Turn the cover of the dust contain-
er in the direction
the cover.
2.3 Pull the filter unit from the dust
container.
2.4 Turn the HEPA filter to remove it
from the coarse filter.
3. You can brush out the HEPA filter. In case of heavy
staining, clean the filters under running water.
4. Let the filters air-dry completely before refitting them!
5. Wipe the dust collector with a damp cloth and then wipe
it dry.
6. Assembly of the filter unit
6.1 The HEPA filter has 3 guide lugs. Set the largest
guide lug into the largest recess of the coarse filter.
Tighten the HEPA filter by turning it clockwise. It must
audibly engage.
6.2 Set the filter unit into the dust
container. The rounded guide lug
must sit exactly in the rounded
recess.
6.3 Reattach the cover to the dust
container. Set the arrow ( ) on the
cover just over the arrow at the
side of the symbol
6.4 Tighten the cover in the direction
engage.
6.5 Reattach the dust container to the motor housing. Set
the dust container first at the bottom part to the motor
housing, so that the electric contacts are matched.
Then engage it to the top. For this, press the smooth
area of the button (1).
Outlet Filter
The appliance is also equipped with an outlet filter. It is on the
right side of the appliance.
CAUTION:
You cannot remove this filter.
. Remove
.
. It must audibly
20.10.16

Werbung

loading