Assembly And Battery Charging; Installing The Charging Station On A Wall; Assembly Of The Appliance; Charging The Battery - Clatronic BS 1305 A Bedienungsanleitung

Assembly and Battery Charging

Installing the Charging Station on a Wall

WARNING:
Make sure beforehand whether there are cables in the wall
which could be damaged!
NOTE:
• A power outlet must be near.
• Assemble the wall holder without the base.
1. Hold the wall holder against the wall and mark the 3
holes.
2. Drill the holes and insert the dowels into the wall.
3. Screw the screws into the dowels and suspend the wall
holder.
4. Tighten the screws by hand.

Assembly of the Appliance

Refer to the illustrations on page 4.
A If you do not want to fasten the charging station to a wall,
set the wall holder onto the base. It must engages. Set
the assembled charging station onto a level, solid surface.
B Connect the power cable to the connection socket on the
charging station.
C Connect the appliance holder with the floor nozzle. It
must engages. Take note of the contact pins on the floor
nozzle.
D Fix the basic unit in the appliance holder.
CAUTION:
The telescopic crevice nozzle must be pushed in! If the
basic unit is set into the appliance holder with extended
crevice nozzle, the crevice nozzle will jam.
First, insert the crevice nozzle into the opening of the
appliance holder. Then push the handle of the basic unit
into the appliance holder. It must audibly engage.
E When you want to charge the battery, hang the complete-
ly assembled appliance into the charging station. Make
sure of stability and correct assembly. The contacts of the
appliance holder must touch the contacts on the charging
station. The 4 contacts must be clean and dry. Otherwise
the battery will not be charged.
F For space-saving storage, you can fold the handle of the
appliance holder. To do this, press the button (13).

Charging the Battery

1. Turn off the device (Position of both switches: O).
2. Connect the mains adapter to a certified wall socket.
Charge the device for 12 - 14 hours before first-time use.
NOTE:
• The pilot lamp flashes during charging.
• The pilot lamp is lit continuously when the battery
has been charged completely.
• It is normal for the device to heat up during charging.
34
BS1305A_IM_new
3. Stop any charging operation after a maximum of
12 hours.
CAUTION:
Always disconnect the plug from the wall socket after
12 hours of charging.
NOTE on battery life:
Observe the following in order to prolong battery life:
• Charge the battery only when it is almost empty.
• Charge the device at an ambient temperature between
0 ° and + 40 °C.

Using the Device

• You can use the appliance as a floor vacuum cleaner or as
a handheld and upright vacuum cleaner (basic unit).
• To separate the basic unit from the appliance holder, press
the button (12) and at the same time use the handle to pull
out the appliance. (Page 5, Fig. G)
• Turn the appliance on or off with the on / off switch (3) or (15).
NOTE:
When you use the appliance as a floor vacuum cleaner, it
can be turned on also with the on / off switch on the basic
unit. In this case, it can be turned off only with the switch on
the basic unit.

Telescopic Crevice Nozzle on the Basic Unit

You can extend the crevice nozzle.
• Pull out the crevice nozzle until the lock (23) on the rear of
the appliance engages.
• To retract the crevice nozzle again, press the unlock
button (23).

Emptying the Collection Container

Refer to fig. K on page 5.
1. Turn off the device (Position of both switches: O).
2. Keep the device horizontal when opening the collection
container.
3. Slide the unlock button (24) and at the same time turn the
motor housing off the catch tray.
4. Pull first the fine dust filter and then the coarse dust filter
from the catch tray.
5. Empty the components.
6. Reinstall the components into the collection container in
reverse order.
7. Proceed as follows to reattach the catch tray to the motor
housing:
Confirm the 3 projections on the motor housing and the
3 recesses on the catch tray. Set the projections into the
recesses and at the same time tighten the motor housing.
The lock (24) must engage.
23.06.16