Cleaning And Storage - Clatronic bs 1262 Bedienungsanleitung

Cable winding device
Pull out the cable up to the maximum length indicated with the
yellow mark. Never pull the cable out up to the red mark as the
cable winding can be damaged. Said damages are not covered
by the warranty.
Winding
Press the cable (4) winding button and guide the cable. Hold the
cable to avoid wrapping.
Nozzle Attachment
Crevice and For vacuuming upholstery, curtains and
jointed nozzle: in corners and crevices etc.
„2-in-1" nozzle: When this is folded toge-
ther it can be used as a groove nozzle.
If you would like to use the brush nozzle,
pull the brush section in the direction of
the arrow until it locks in place.
Floor nozzle: To clean carpets or smooth surfaces.
Smooth Press down the lever with the brush symbol
fl oors: with your foot. The brush is now visible.
Carpets: Press the lever In the opposite direction.
The brushes are now retracted.
Releasing the Pull these off while turning slightly.
nozzles:
Air Slide
Open the air slide on the hose handle in order to regulate the
airfl ow or to clear any particles sticking to the nozzle.
Dust bag replacement display (6)
Hold the hose up into air. If the dust bag change display lights
up, the bag is full. Please change it.
Changing the dust bag
• Pull the plug out of the socket.
• Open the lid of the dust bag compartment by the handle (7).
• Remove the bag by pulling the retainer carefully upwards so
that you have easier access to the bag. Then remove the
dust bag by pulling it upwards.
• Insert a new bag. Please ensure that the bag is located
correctly in the guide mechanism. Then reinsert the retainer.
Close the cover so that it snaps into place.
Your appliance has two fi lters.
Motor protection fi lter (inlet fi lter)
The inlet fi lter is located in the dust bag compartment. The fi lter
is located vertically in the rear section of the dust housing.
• Remove the fi lter by pulling upwards.
• Clean the engine protection fi lter after 10 dust bag changes.
If necessary, the fi lter can also be washed in warm water
without any additives.
05-BS 1262 PLUS 27
Filter
• Place it back into place only once it is completely dry!
Outlet fi lter
The appliance is also equipped with an outlet fi lter. This fi lter is
to be found under the fi lter cover (8).
• Open the ventilation grille by pressing together the lever on
the side of the ventilation grille.
• Then pull the grille out towards the front.
• Remove the fi lter and clean as described above.
• Please re-insert the fi lter correctly and close the ventilation
grille (until it clicks in place).

Cleaning and storage

Cleaning
• Pull the plug out of the socket before cleaning!
• Clean the casing with a dry cloth.
Storage
• Let the iron cool down completely.
• Wind the cable completely.
• If you position the device horizontally: Please insert the hook
of the fl oor nozzle into the parking assistant on the rear of
the device.
• If you place the vacuum cleaner in a vertical position: Please
hang the hook of the fl oor nozzle in the parking aid on the
underside of the vacuum.
Troubleshooting
• The Device Does Not Work.
Remedy:
Check the connection to the mains.
Check the position of the switch.
• The device does not suck up anything.
Possible Cause:
The suction power is set too low.
Remedy:
Check the position of the control switch.
Possible Cause:
The dust bag is full.
Remedy:
Renew the dust bag.
or
Possible Cause:
The fi lters are dirty.
Remedy:
Clean the components.
Possible Cause:
There is a foreign body in the suction tube or the nozzle.
Remedy:
Check the accessories for foreign bodies.
27
14.11.2006, 12:54:15 Uhr