Before First Use; Operation - Scheppach 5911208903 Originalbetriebsanleitung

Information concerning noise emission measured
according to relevant standards:
Sound pressure L
Sound power L
Uncertainty K
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A (left/right) = 6.81 m/s
hv
Uncertainty K
PA

7. Before first use

Before starting the equipment
Assembling the components
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the inst-
ructions below.
Important! You will need the following additional tools
(not supplied) for assembly, and also for mainte-
nance work:
• A 1 liter measuring jug (oil/petrol resistant)
• A petrol can (5 liters is sufficient for approx. 6
operating hours)
• A funnel (suitable for the tankʼs petrol filler neck)
• Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
• A petrol suction pump (plastic, available from DIY
stores)
• An oil can with hand pump (available from DIY
stores)
• 0,6 liter of engine oil (SAE 30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all p arts are present.
2. Attach the hole of the lower push bar on the pin of
the mower, then fix the lower push bar with a screw
and an star grip nut to both sides of the mower.
Make sure that the cables, which will be attached
later, are not in the way (Fig. 2-3).
3. Attach the upper push bar (4) on the lower push
bar with one quick-release lever (5) and one plastic
nut each on both sides (Fig. 4). Note the correct
alignment of the quick-release lever bracket ensu-
ring the quick-release function remains intact.
4. Insert the pull start handle in the designated hook
as shown in Fig. 5.
5. Fix the cables to the push bar with the cable clips
provided (Fig. 6).
6. Grass box (16) - open it up and click the plastic
clips into position on the frame (Fig. 7).
7. Mowing with grass box:
Lift the discharge flap (Fig.1/No. 15) with one hand
and hang the grass box (Fig.1/No. 16) as shown in
Fig. 8.
8. Mowing with side discharge:
Lift the side discharge flap and mount the side
discharge cover (18) (Fig. 9). If the grass box is
attached, remove it and replace it with the mulch
insert.
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002- 58 internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002- 58
= 84.7 dB(A)
pA
= 95.1 dB(A)
WA
= 3 dB(A)
2
= 1.5 m/s
2
9. Mulching:
If the grass box (16) is attached, remove it and
replace it with the mulch insert (19) as shown in
Fig. 10-12.
Caution:
The side discharge cover must not be installed.
Setting the cutting height
m CAUTION!
Adjust the cutting height only when the engine is
switched off and the plug boot has been pulled.
• Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged.
• To prevent any imbalance, replace blunt and/or
damaged blades as a set only (if applicable). To
carry out this check, first switch off the engine and
pull the spark plug boot.
• The cutting height is centrally adjusted with the
cutting height adjustor lever (Fig.13/ Item 14). 8
different cutting heights can be selected.
• Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position. (Fig. 13)

8. Operation

m CAUTION!
The engine does not come with oil in it. Therefore,
ensure that you add 0,45 liters of oil before starting
it up. Use normal, multigrade oil (SAE30). The oil
level in the engine must be checked each time before
mowing.
You will also need to fill in petrol, as this is also not
supplied upon delivery.
• In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig. 1/ Item 3) which must be pulled back
before the engine can be started. When the engine
control lever is released it must return to its initial
position, at which point the engine automatically
switches off.
• Press the engine brake lever (3) together and give
the starter cord (17) a vigorous pull.
Attention:
When you pull the starting rope the cutting blade
rotates even when dissolved motor brake lever.
Make sure that there are no body parts in danger
zone of cutting blade.
• When the engine is running, press the drive lever
(2) to the handle (1) in order to engage drive on the
mower.
• You can control the rotation speed of the blade
using the throttle control lever (20) (Fig. 14). Al-
ways mow with high engine speed.
• You can control the mower speed with the speed
control lever (8). (Fig. 14).
• Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
DE GB FR
FR FR
25 / 48