Silverline 633629 Bedienungsanleitung Seite 10

EN
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Always disconnect the tool from the air supply before adjustment or maintenance
is carried out.
Fitting the quick connector
This tool is supplied with two different male airline quick connectors (Fig. I):
EQ-4 – commonly used in Europe
EN-6 – mainly used in the UK
• Please choose the connector that is compatible with the airline system you are using, and install
as outlined below:
1. Apply PTFE tape (not included) to the screw threads of the Quick Connector (5). This will help to
maintain an airtight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not come off when the thread
is screwed into the tool.
2. Remove the protective plug from the air inlet
3. Using a spanner (not included) screw the quick connector into the air inlet located at the base of
the handle
4. Connect to airline, pressurise carefully and carry out a leak check (e.g. by spraying small amounts
of soapy water on to the outside of the connectors)
• Air lines fitted with matching female quick connectors will now be a push fit to the tool
WARNING: Do not attach the tool to a hose and the hose to a compressor with only threaded
connections. Always use quick connectors so the tool can be removed from the air supply connection
when needed for safe operation.
WARNING: Never fit a female quick connector directly to the leader hose/whip hose or directly
to the tool. The stored pressurised air in the tool, even when detached from the main air supply, can
operate the tool unexpectedly.
Air supply connection
WARNING: Under no circumstances can the spray gun be used in a compressed air system with
integrated oiler.
• This tool should be connected to a clean, dry air supply with water separator and filter.
• Do not allow supply pressure to exceed the maximum stated (see 'Specifications')
• Ensure that water is drained from air system daily
• Ensure that all parts of the system (hoses, couplers, etc.) are correctly rated for the air pressure to
be used
• Use conductive hoses to help prevent build-up of electrostatic charge
Setting tool power
• The tool power can be adjusted by reducing/increasing the air supply pressure within the range
specified in 'Specifications'
Setting up the sandblasting gun assembly
1. Ensure the sandblasting gun has been correctly assembled, and the Nozzle Locking Ring (2) has
been securely tightened
2. Connect one end of the Rubber Hose (6) to the Suction Nozzle (7) and the other end of the hose
to the Material Hose Connector (3)
Note: It is recommended to use conductive hose to connect the sandblasting gun and
Suction Nozzle.
3. Fill a suitable container with abrasive material
4. Immerse the Suction Nozzle in the abrasive material, so that the tip of the Deaeration Pipe (9)
protrudes above the surface of the abrasive material
10
Preparing the workpiece
• Workpieces contaminated with oil and grease should be degreased prior to sandblasting
• Remove dirt and other encrustations (e.g. dried mud, soil) from surfaces before sandblasting
• Carefully cover areas of the workpiece that must not be sandblasted (e.g. insides of engine
blocks, cylinder bores, and other functional surfaces)
Operation
WARNING: Always wear personal protection equipment, including eye protection, suitable
gloves and adequate respiratory protection, when working with this sandblaster.
1. Connect the sandblasting gun to the air supply
2. Adjust the air supply pressure according to the workpiece and abrasive used
WARNING: Ensure the air supply pressure does not exceed the maximum operating pressure
stated in 'Specifications' .
IMPORTANT: Ensure the pressure is suitable for the workpiece and does not damage the surface.
ALWAYS test the effect of the abrasive on a scrap piece of material, or begin sandblasting at an
inconspicuous place on the workpiece before starting the main job.
3. Direct the Outlet Nozzle (1) towards the workpiece and press the Trigger (4) to start the flow of
abrasive
Note: When the Suction Nozzle (7) and Rubber Hose (6) are empty, it may take a few seconds for the
abrasive to start flowing into the sandblasting gun. Keep the Trigger depressed until the abrasive
exits the Outlet Nozzle.
4. Release the Trigger to stop sandblasting
WARNING: Be aware that air tools may hold residual pressure after use. Always bleed air
pressure from the tool after shutting off air supply.
Nozzle blockage
If the flow of the sanding material is reduced or stops completely, there may be a blockage in the
nozzle:
1. Disconnect from the air supply
2. Undo the Nozzle Locking Ring (2) and remove the Outlet Nozzle (1)
3. Check for and remove any clogged material in the Outlet Nozzle and the gun
4. Reconnect to the air supply
5. Remove the Suction Nozzle (7) from the abrasive container and activate the gun to blow through
the system until it's clear
6. Disconnect from the air supply and replace the Outlet Nozzle
• If the Outlet Nozzle is clear but the sanding material is still restricted, check the Rubber Hose (6)
and the Suction Nozzle for clogging and remove any clogged material
• See the 'Troubleshooting' section for possible causes of clogging and the relevant solution
Maintenance
WARNING: Always disconnect from the air supply and depressurise before cleaning or carrying
out any maintenance.
IMPORTANT: There is very little that can go wrong with your air tool and it should be noted that
when an air tool fails to work it is generally because the internal workings have corroded due to
dirty, wet air and failure to follow the operating instructions.
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth
1. Before disassembly, reconnect the sandblasting gun to the air supply
2. Remove the Suction Nozzle (7) from the abrasive container
3. Direct the Outlet Nozzle (1) towards a safe place, and blow it through with air until all remaining
abrasive is removed
4. Disconnect from the air supply
5. Remove the Rubber Hose (6) from the Material Hose Connector (3) and Suction Nozzle Hose
Connector (8)
6. Remove the Nozzle Locking Ring (2) and Outlet Nozzle (1). Disassemble other components as
necessary, referring to the 'Assembly Diagram'
7. Clean the whole route of abrasive material thoroughly, taking care not to damage the Outlet
Nozzle (1) and other internal parts
8. Slightly lubricate all sealing surfaces and moving components with a suitable spray gun
lubricant
9. Reassemble the sandblasting gun, referring to the 'Assembly Diagram'