Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Using On-Screen Menus
4PRESET menu
You can preset each control to a desired level and set it.
If you set PRESET to ON, the REMOTE indicator
lights up and the controls on the front panel do not
work. The monitor operates with the internal memory
settings. For adjustment, select the PRESET ADJUST
screen.
5 CONFIG menu
Select an item for adjustment of the monitor.
6 PRESET ADJUST screen
Adjust CONTRAST, BRIGHT, CHROMA, PHASE,
VOLUME, APERTURE in the PRESET menu.
7 CHROMA SET UP menu
Set to ON to adjust the internal decoder for CHROMA
and PHASE (NTSC signal only) after AUTO ADJUST
screen (!™).
8 RGB A SYSTEM menu
To monitor the signal fed through the RGB/
COMPONENT A connectors, set the RGB or COMP
(component) signal and the INT SYNC (internal sync)
or EXT SYNC (external sync) signal in this menu.
9 RGB B SYSTEM menu
To monitor the signal fed through the RGB/
COMPONENT B connectors, set the RGB or COMP
(component) signal and the INT SYNC (internal sync)
or EXT SYNC (external sync) signal in this menu.
!º REMOTE (RS-232C) menu
Select one out of following three modes.
REMOTE OFF:
You can adjust settings and controls by the buttons
and controls on the front panel.
The RS-232C connector does not function.
REMOTE ONLY:
You can adjust settings and controls through the
RS-232C connector.
Buttons and controls on the front panel, except the
menu operation ones, do not function.
REMOTE & LOCAL:
You can adjust settings and controls both through the
RS-232C connector and the front panel buttons.
Controls on the front panel do not function.
!¡ LANGUAGE menu
You can select the language used for on-screen menus
from the following five languages (English, German,
French, Italian, Spanish).
14
!™ AUTO ADJUST screen
[OFF]
The user service mode is useful when adjusting the settings
and controls except for the above.
To enter the user service mode, press the MENU (EXIT)
button when the main menu is not displayed and hold it
until the following USER SERVICE 1 appears.
To move to the second page of the mode, select "NEXT
PAGE" and to return to the first page, select "PREVIOUS
PAGE".
[OFF]
[RGB-EXT SYNC]
!£ USER COLOR TEMP ADJUST menu
[RGB-EXT SYNC]
!¢ COLOR SYSTEM DISPLAY menu
[REMOTE OFF]
!∞ 358 TRAP FILTER menu
[ENGLISH]
Select the color bar signal (full, SMPTE, EIA) and press
the ENTER (SELECT) button to start automatic
adjustment for CHROMA and PHASE. For these
adjustments to be valid, you must select ON in
CHROMA SET UP menu (7).
User Service Mode
ENTER
MENU
The value of adjustment in this menu works only when
"USER" is selected in the COLOR TEMP SELECT
menu (3).
ADJUST GAIN:
Adjusts the color balance (gain) of the USER mode.
ADJUST BIAS:
Adjusts the color balance (bias) of the USER mode.
COLOR TEMP RANGE:
When you adjust the color temperature in the USER
mode, select a color temperature range before
adjusting ADJUST GAIN and ADJUST BIAS. If the
adjusted color temperature is between 3200K and
5000K, select "3200K-5000K." If the adjusted color
temperature is between 5000K and 10000K, select
"5000K-10000K."
USER COPY:
Selects the color temperature of the USER mode
from among D65(6500K+8MPCD),
D56(5600K+8MPCD) and D93(9300K+8MPCD).
Select the color system display mode. In AUTO, the
kind of color system being used appears on the screen
each time you change the signal input.
Color spill or color noise may be eliminated if you
select ON (NTSC signal only). Normally set it to OFF.
ENTER
MENU
[5000K-10000K]
[AUTO]
[OFF]
Werbung
