Chicco Hoopla Gebrauchsanleitung Seite 12

• WARNING: This toy must only be
used under adult supervision.
• WARNING: Check the toy regularly
for signs of wear and damage and
to ensure that it is assembled cor­
rectly. Should any parts on the toy­
bar or hanging toy be damaged,
do not use them and keep out of
reach of children.
• Keep the product out of children's
reach when it is not being used.
CARE AND MAINTENANCE
• This product requires periodical maintenance.
• The cleaning and maintenance operations must only be carried
out by an adult.
• Periodically inspect the reclined cradle to check for broken, torn or
missing parts: If this is the case, do not use it.
• Please refer to the care label for instructions on cleaning the product.
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
• Check that the fabric and stitching are in good condition each
time you wash it.
• Prolonged exposure to direct sunlight can cause the fabric to fade.
COMPONENTS
A ­ Base
B ­ Feet
B1 ­ Non­slip rubber
B2 ­ Open/close buttons
C ­ Seat
D ­ Booster cushion
E ­ Toybar
F ­ Slider ring
G ­ Toys*
H ­ Toybar coupling holes
I ­ Fastening straps
L ­ Buckles
M ­ Clips
N ­ Ring for the adjustment of the safety harness
O ­ Reclining button
P ­ Click buttons
Q ­ Seat buttonhole
ASSEMBLY
The reclined cradle comes already assembled. To use it, the follow­
ing operations must be performed:
1. To open the reclined cradle pull the seat upward (Fig. 1), when
you hear it click, it means the product is correctly opened. Make
sure that both sides of the reclined cradle are properly open.
2. Fasten the toybar on both sides by fitting the lower ends of the
bar into the relevant coupling holes (Fig. 2).
At this point you can choose the position you prefer.
HOW TO ADJUST THE BACKREST
3. To adjust the backrest from a higher position to a more inclined
one, take the two side buttons (Fig. 3) and pull them upward, keep­
ing them pressed down; choose the desired reclining within the 4
available positions. This operation may also be carried out with the
child sitting in the reclined cradle. In this case it can be more difficult.
WARNING: Always guide the backrest with the fingers when ad­
justing the reclining.
To move from the highest inclined position to a lower inclination,
just pull the backrest upward (Fig. 4­5).
WARNING: Always check that the backrest is properly locked be­
fore use.
FIXED OR ROCKING MODE
4. The reclined cradle can be used in fixed or rocking mode:
• Fixed mode: turn the front feet (B) clockwise until the lower part of
the foot touches the ground (Fig. 6);
• Rocking mode: turn the front feet (B) in the opposite direction (coun­
ter­clockwise), so that the foot is not touching the ground (Fig. 7).
HOW TO CLOSE THE CHAIR
5. The reclined cradle can be closed for transport.
WARNING: The reclined cradle must never be closed with the
child sitting in it. Remove the child from the reclined cradle before
closing the frame!
6. To close the reclined cradle, press the 2 buttons inside the front
feet (Fig. 8) simultaneously.
7. To open the reclined cradle again, just pull the seat upward (Fig. 9)
until you hear a click that indicates the correct opening.
USING THE SAFETY HARNESS
8. The safety harness is pre­fitted and ready for use the first time you
use the reclined cradle (Fig. 10).
To release them, press the ends of the prong of the buckle and pull out
the buckle (Fig. 11). The bouncer is ready for the child.
WARNING: When using, always remember to fasten the belt by
passing it around the crotch strap and check it is tight enough and
in the right position.
It is possible to alter the tightness of the belt by adjusting it and passing
the fabric around the back of the backrest.
9. Keep one clasp end blocked and simultaneously pull the belt
and slide it inside the relative ring (N), to adjust the tension of the
safety harness (Fig. 12).
BOOSTER CUSHION
10. The reducer cushion D is ideal from birth and can be removed
according to needs. To fix it to the seat, place it on the seat and
slide the crotch strap through the hole (Fig. 13). Thread the safety
harness in the relative side slots of the reducer cushion (Fig. 13A).
TOY BAR
11. Fasten the toy bar (E) to the frame inserting the lower ends in the
relevant fastening holes of the bar support (Fig. 14).
WARNING! Always check that the toybar is properly fastened before
every use.
12. The toys can be fixed to the toy bar inserting the upper ends in
the relevant holes in the fabric bar (Fig. 15). A different fastening
point can be chosen for each toy. The toys can also be inserted
in the two slider rings "F" on the arcs of the toy bar (Fig. 16): the
SlideLine system lets you slide the toys along the arc and to
change the play scenarios whenever you want.
HOW TO REMOVE THE FABRIC COVER
It is possible to remove the seat cover and the booster cushion from
the reclined cradle to wash them.
13. Remove the booster cushion (Fig. 17).
14. Pull the waist belt out of the textile hole and the 2 plastic rings
on the reclined cradle frame and start pulling the lining off from
the front. Release the 4 click buttons P at the side under the metal
tubes (Fig. 18), remove the Velcro strap under it (Fig. 19 ­20), then
take off the fabric through the entire frame paying attention not
to damage it. To refit the cover, proceed in reverse order, mak­
ing sure that the lower fabric strap goes through the adjustment
joints of the backrest (Fig. 21) and the toybar supports.
* The theme of the detachable toys varies depending on the se­
lected set.
12