Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there is
still a slight risk of accident or injury when using the
device. Stay alert and use common sense when using
the device.
3. USE GUIDELINES
The device is designed for kneading, grinding, chopping,
cutting, mixing or whipping food products of different
consistencies using a suitable attachment such as a jug, bowl
or grinder.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
4
3
6
10
5
8
12
13
1
2
9
7
11
1.
Bowl
2.
Lock button for the upper part
3.
Blender jug
4.
Dough hook
5.
Upper part
6.
Wire whip
7.
Lower part
8.
Flat beater
9.
Speed control / device on/off switch
10.
Plug for the jug mounting hole
11.
Base
12.
Bowl lid with feeding hole
13.
Beater mounting bracket
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. There should be at least 10 cm distance
between each side of the device and the wall or other
objects. Keep the device away from hot surfaces. Operate
the device on an even, stable, clean, fire-proof and dry
surface and out of the reach of children and persons with
mental disabilities. Position the device such that you always
have access to the power plug. The power cord connected
to the appliance must be properly grounded and
correspond to the technical details on the product label.
Disassemble the device and all its components and clean
them before the first use.
3.3. DEVICE USE
ATTENTION! Before replacing the accessories, make sure
that the speed controller with the switch is in the off
position and the power cord is not connected.
EN
3.3.1. FIRST RUN
1.
Unlock the upper part of the device with the lock
button and lift it.
2.
Place the bowl on the base and lock it in the direction
indicated by the arrow.
3.
Attach the bowl lid to the bottom of the upper part of
the device, then insert and lock the selected beater.
4.
Release the upper part lock button, then lower the
upper part towards the base.
5.
Ensure that the upper part is positioned properly on
the base. Lock the upper part with the lock button.
6.
Connect the device to the power supply and test each
speed for a few seconds.
7.
At the end of the test, set the speed controller to the
off position (0). Disconnect the device from the power
supply.
8.
Release the upper part and lift it. Remove the beater.
9.
Release the lock button and lower the upper body
towards the base.
10.
Ensure that the upper part rests properly on the base,
then lock the upper part with the lock button.
11.
Remove the blender mounting hole plug. Lock the
blender jug.
12.
Pour a glass of water into the blender jug and lock the
jug into the device.
13.
Remove the blender jug and replace the blender
mounting hole plug..
3.3.2. SELECTING PROPER BEATER AND ROTATION SPEED
ATTENTION: Before starting work, select the beater to match
the type and speed of mixing.
•
Dough hook is used for kneading dense and heavy
dough at the lowest rotation speed.
•
Flat beater is used to mix light dough and icing at
medium speed.
•
Wire whip is used to whip and aerate the lightest
masses, e.g., eggs or cream, at high speed.
NOTE: All beaters use planetary motion. The device user
can choose the beater rotation speed. Speeds are marked
with numbers from „1" to „6", where „1" is the minimum
speed and „6" is the maximum. Setting the speed controller
in the "off" position turns off the speed. Setting the speed
controller in the „P" position means peak rotation power –
pulse mode.
NOTE: When mixing dense ingredients, do not switch on
high speed because the device may be damaged. Adjust the
speed of the beater to the type of ingredients. If the device
vibrates, moves too much, etc., reduce the speed until the
unwanted movement stops.
3.3.3. MIXING
IMPORTANT!
The maximum mixing time is 4 minutes.
NOTE: Do not insert hands or any other objects into the
bowl while mixing the ingredients. Also grasping the bowl
or beater during operation is dangerous and therefore
forbidden.
1.
Make sure that the speed controller is in the "off"
position and the power cord is not connected to the
mains.
2.
Release the upper part of the device with the lock
button and lift it.
3.
Place the bowl on the base and lock it in the direction
indicated by the arrow.
4.
Attach the bowl lid to the bottom of the upper part,
then insert and lock the beater chosen for the work.
10
5.
Place the ingredients in the bowl. Take care not to
exceed the amount that could cause them to escape
the bowl.
6.
Release the upper part lock button and lower the
upper part towards the base.
7.
Ensure that the upper part rests properly on the
base. Lock the upper part with the lock button.
8.
Connect the device to the power supply.
9.
Turn the speed controller from the "off" position to
the desired „1-6" or „P" position.
10.
As you work, add ingredients through the hole in the
lid. It is forbidden to open the lid during operation.
11.
If the ingredients stick to the walls of the bowl and
need to be detached, first turn off the device and
wait for the rotating parts to stop, then clean the
bowl with a silicone spatula.
12.
After finishing work, turn the speed controller to the
"off" position, then disconnect the device from the
power source.
13.
After dismantling and emptying the bowl, wash it. Do
the same with the beater and the bowl lid with the
feeding opening.
3.3.4. BLENDING
Important! The maximum blending time is 3 minutes.
1
2
3
1.
Stopper / measure
2.
Lid
4
3.
Glass jug
5
4.
Gasket
5.
Blade unit
6
6.
Jug base
Assembly
1.
Place the rubber O-ring on the inside edge of the
blade unit.
2.
Place the blade unit with the O-ring in the jug base.
3.
Insert and tighten the glass jug in the base all the
way (in a clockwise direction).
4.
Mount the assembled jug in the device.
5.
After inserting the ingredients into the jug, attach
the lid by pushing it down.
6.
Insert the stopper into the lid hole and turn it
counter clockwise to lock it..
Operation
1.
When filling the jug, make sure not to exceed the
maximum allowed amount of ingredients.
2.
After inserting the ingredients into the jug, attach
the lid by pushing it down.
3.
Insert the stopper into the lid hole and turn it
counter clockwise to lock it..
4.
Set the speed:
•
Speed: „3-4" for light consistency (liquids),
EN
•
Speed: „5-6" for more solid consistency (mixing of
liquids and solid food products),
•
Speed: „P" for ice crushing and short, strong
movements (the knob stops permanently in the „P"
position, you must hold the knob after turning it or
turn it several times towards „P")
5.
After blending, set the switch to „0" speed.
Disconnect the device from the power supply.
6.
To take out the glass jug, simply lift it. Do not turn
the glass jug to remove it.
7.
After using the device, plug the blender lock hole.
3.4. CLEANING AND MAINTENANCE
a)
Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used. Wait for the rotating elements to stop.
b)
Use only mild, food-safe detergents to wash the
device.
c)
After cleaning the device, all parts should be dried
completely before using it again.
d)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e)
Never spray the device with water.
f)
Do not allow water to get inside the device through
vents in the housing of the device.
g)
Clean the vents with a brush and compressed air.
h)
The device must be regularly inspected to check its
technical efficiency and spot any damage.
i)
For cleaning, use non-scratch utensils. Do not use
sharp or metal tools.
j)
Do not use any abrasive detergents or alcohol when
cleaning the inside and outside of the appliance.
k)
The dough mixers, loading tray, loading tube and
screw are not suitable for washing in a dishwasher.
Wash them in warm water using dishwashing liquid.
l)
Plastic accessories, mixing bowl, whipping agitator,
jug and blades inside the blender can be cleaned
with warm water and dishwashing liquid or in
a dishwasher. Do not use caustic detergents.
11
Werbung
