Ryobi RC18120-120 Bedienungsanleitung Seite 11

Safety, performance, and dependability have been given
top priority in the design of your charger.
INTENDED USE
This charger is only intended to charge RYOBI ONE+
Lithium-Ion battery packs listed in this manual.
The product is only for use indoors in dry conditions.
The product is not intended to charge any other type
of battery, to be used as a power supply, or for any
other purpose. It should never be used in explosive or
CHARGER SAFETY WARNINGS
Please read and observe these instructions before using the
product. Failure to follow these instructions and warnings
WARNING
Do not recharge primary cells (non-rechargeable).
WARNING
Mains voltage must correspond with the voltage
Before using the product, check that the product
enclosure, cable and adaptor plug are not damaged.
If damage is found, do not use and follow instruction in
the maintenance section of this manual.
The product must not be damp, and should never be
used in a damp environment.
The product is for indoor use only.
Do not use the product if it has suffered any heavy
shock or jolting, or is damaged in any other way.
Do not conduct charging in a position which may
become exposed to sunlight or other heat source.
Due to the heat generated during charging, the product
should not be operated on a combustible surface.
Do not conduct charging operations in the vicinity
of flammable materials. Example: Cloth, packaging
materials, paint, spray paint or aerosols, lubricant,
thinners, petrol containers, gas containers or gas
appliances.
Do not cover any ventilating slots and provide adequate
ventilation during operation.
Never modify, disassemble or attempt to repair the
product yourself.
Do not allow the charger or batteries to become
contaminated with any material which could be
conductive. Example: Metal particles from grinding,
cutting or machining processes.
Remove the plug of the product from the power socket
when it is not in use or when cleaning it.
Only use extension cable that is approved and in good
condition.
Protect battery contacts to avoid a short circuit caused
by metallic objects which could cause a fire or explosion!
Do not charge batteries which show signs they have
leaked electrolyte. Dispose of them properly.
Never charge a damaged battery pack. If damaged,
replace immediately.
If the battery is not going to be used for a while, remove
the charger plug from the power socket and take the
battery off the product.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
damage due to a short circuit, never immerse your
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
KNOW YOUR PRODUCT
See page 100.
1. Battery port
2. Adaptor
3. Red LED
4. Green LED
5. Key hole hanger
OPERATION
CHARGING THE BATTERY PACK
Battery packs are shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
battery pack under normal circumstances, return both
the battery pack and charger to your nearest authorised
service center for electrical check.
Do not charge nickel cadmium (NiCd) battery packs. When
a NiCd battery pack is inserted, the red LED will light up
Make sure the power supply is normal household voltage,
220 V – 240 V, 50 / 60 Hz 60 W, AC only.
NOTE: After charging is complete, the green LED will
remain on until the battery pack is removed from the
charger or charger is disconnected from the power supply.
1
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL