Siemens SINUMERIK 840D sl Handbuch Seite 1812

Index
Isd-Regler Integralanteil Abschaltschwelle
p1730[0...n], 1129
Isd-Regler Integralanteil Begrenzung
r1725, 1128
Isd-Regler Kombistrom Zeitkonstante
p1731[0...n], 1129
Isd-Stromreglervorsteuerung Skalierung
p1702[0...n], 1124
ISO_ENABLE_DRYRUN
52804, 664
ISO_ENABLE_INTERRUPTS
52802, 664
ISO_M_DRILLING_AXIS_IS_Z
55800, 708
ISO_M_DRILLING_TYPE
55802, 708
ISO_M_ENABLE_POLAR_COORD
52800, 664
ISO_M_RETRACTION_DIR
55806, 708
ISO_M_RETRACTION_FACTOR
55804, 708
ISO_M_TAPPING_SET_MC
55807, 708
ISO_SCALING_SYSTEM
52806, 664
ISO_SIMULTAN_AXES_START
52808, 664
ISO_T_DEEPHOLE_DRILL_MODE
52810, 665
ISO_T_DWELL_TIME_UNIT
55810, 709
ISO_T_RETRACTION_FACTOR
55808, 708
Isq-Regler Integralanteil
r1719, 1126
Isq-Stromreglervorsteuerung EMK Skalierung
p1704[0...n], 1124
Isq-Stromreglervorsteuerung Skalierung
p1703[0...n], 1124
Isttopologie
r9901[0...n], 1706
Isttopologie Indizes Anzahl
r9900, 1705
Istwertkorrektur Bewertungsfaktor Lsig
p1845[0...n], 1154
Istwertkorrektur Dämpfungsfaktor
p1846[0...n], 1154
Istwertkorrektur Konfiguration
p1840[0...n], 1153
Istwertkorrektur Phasenspannungen
r1849[0...5], 1155
1812
Istwertkorrektur Phasenströme
r1848[0...5], 1155
Istwertkorrektur Statuswort
r1841, 1153
J
J_MEA_CAL_HEIGHT_FEEDAX
51772, 647
J_MEA_CAL_RING_DIAM
51770, 647
J_MEA_COLL_MONIT_FEED
51757, 647
J_MEA_COLL_MONIT_POS_FEED
51758, 647
J_MEA_FIXPOINT
52750, 663
J_MEA_FUNCTION_MASK_PIECE
54780, 686
J_MEA_FUNCTION_MASK_TOOL
54782, 686
J_MEA_M_DIST
51750, 646
J_MEA_M_DIST_MANUELL
51751, 647
J_MEA_M_DIST_TOOL_LENGTH
51752, 647
J_MEA_M_DIST_TOOL_RADIUS
51753, 647
J_MEA_MAGN_GLAS_POS
52751, 663
J_MEA_PROTOCOL_FILE
55774, 707
J_MEA_T_PROBE_APPR_AX_DIR
51784, 648
J_MEA_T_PROBE_APPR_MODE
52780, 663
J_MEA_T_PROBE_DIAM_RAD
51780, 648
J_MEA_T_PROBE_MEASURE_DIST
51786, 648
JOG_ACCEL_GEO
21166, 308
JOG_AND_POS_JERK_ENABLE
32420, 453
JOG_AND_POS_MAX_JERK
32430, 454
JOG_CIRCLE_CENTRE
42690, 603
JOG_CIRCLE_END_ANGLE
42694, 604
Listenhandbuch, 10/2015, 6FC5397-7AP40-5AA3
Maschinendaten und Parameter