Ec Declaration Of Conformity; Technical Specifications; Warranty - STEINEL XLED PRO Square Bedienungsanleitung

Sensor mode: (Fig� 6�2)
– Switch light ON (when light is OFF):
– Switch OFF and ON once. Light stays ON for
the period selected.
– Switch light OFF (when light is ON):
– Switch OFF and ON once. Light goes out or
switches to sensor mode.
Manual override: (Fig� 6�2)
– Activate manual override:
– Turn switch OFF and ON twice. The floodlight is
set to manual override for 4 hours (status LED
ON). Then it returns automatically to sensor
mode (status LED OFF).
– Deactivate manual override:
– Switch OFF and ON once. The floodlight goes
out or switches to sensor mode.
Important:
The switch must be actuated in rapid succession
(in the 0.2 - 1 s sec. range).
Reach adjustment
Depending on mounting height, the detection zone
setting can be optimised to suit requirements.
The film shroud can be used for masking out any
number of lens segments to limit reach as required.
Inadvertent triggering is ruled out or the sensor can
be targeted to watch over danger spots.
– limited at side (Fig� 6�3)
– limiting reach (Fig� 6�4)
Other:
– Floodlight adjustment range (Fig� 6�5 / 6�6)
7� Information
Reference to light-distribution curves (Fig� 7�1-7�4)
8� Accessories (optional)
Remote control RC 9 (EAN 4007841007638)
The XLED PRO provides additional functions by
using the RC 9 remote control. The optional RC 9
remote control makes it easier to install larger-type
lighting systems as it is then no longer necessary to
set each light before it is installed. Any number of
floodlights can be controlled via remote control.
Remote control functions
1. Brightness setting
2. Daylight mode
3. Night mode
4. Teach mode
5. Time setting
6. Any chosen light ON time
7. Manual override
8. Install mode
9. Reset
Smart remote (optional)
(EAN 4007841009151)
– Control via smartphone or tablet
– Replaces remote control
– Load appropriate app and connect by Bluetooth
9� EC Declaration of Conformity
This product complies with the requirements
defined in the following standards, legislation and
directives:
– Low Voltage Directive 2014/35/EU
– EMC Directive 2014/30/EU
– RoHS Directive 2011/65/EU
– WEEE 2012/19/EU
– 14 –
10� Technical specifications
Sensor-switched LED XLED PRO Square XL and XLED PRO Square
floodlights XLED PRO Wide XL and XLED PRO Wide
Dimensions (W x D x H) XLED PRO Square XL and XLED PRO Square: 230 x 178 x 130 mm
XLED PRO Wide XL and XLED PRO Wide:
Voltage supply 220 - 240 V / 50 / 60 Hz
Output XLED PRO Square XL / Wide XL 48 W
XLED PRO Square / Wide 24.8 W
Sensor technology PIR (passive Infrared)
Colour temperature 4000 K (neutral white) SDCM 3
Colour rendering index Ra > 80
Luminous flux XLED PRO Square XL / Wide XL
XLED PRO Square / Wide
Basic light 10 min, 30 min (by RC 9), all night
LED life expectancy 50,000 h (L70B10 to LM80)
Angle of coverage 240°
Detection reach 12 m (mounting height 2 m to 6 m max.)
Adjustment range 0-90° tilting
360° swivelling
Area illuminated XLED PRO Square 362 cm
XLED PRO Wide
Time setting 5 s - 15 min (control dial)
5 s - 60 min (smart remote)
10 s - 15 min (RC 9)
Twilight setting 2-1000 lux (potentiometer)
2-1000 lux, infinitely variable (smart remote)
2, 10, 30, 50, 100 lux, daylight mode (RC 9)
Programme setting OFF = no basic light level, 10 min, all night (potentiometer)
OFF, 10 min – 30 min, all night (smart remote)
Manual override (permanent light) 4 h, adjustable ( button, RC 9, smart remote)
IP rating IP 54
Protection class I / IK03
Temperature range -20°C to +40°C
11� Warranty
All rights are based on our warranty period. We
guarantee that your STEINEL Professional sensor
product will remain in perfect condition and proper
working order for a period of 5 years. We guaran-
tee that this product is free from material, manufac-
turing and design flaws. In addition, we guarantee
that all electronic components and cables function
in the proper manner and that all materials used
and their surfaces are without defects.
188 x 265 x 126 mm
4400 lm, 91.7 lm/W
2400 lm, 96.8 lm/W
2
403 cm
2
Making Claims
If you wish to make a claim, please send your
product complete and carriage paid with the origi-
nal receipt of purchase, which must show the date
of purchase and product designation, either to your
retailer or contact us at STEINEL (UK) Limited,
25 Manasty Road, Axis Park, Orton Southgate,
Peterborough, PE2 6UP, for a returns number.
For this reason, we recommend that you keep
your receipt of purchase in a safe place until the
warranty period expires. STEINEL shall assume
no liability for the costs or risks involved in returning
a product.
For information on making claims under
the terms of the warranty, please go to
www�steinel-professional�de/garantie
– 15 –