Pulsar QUANTUM HD19S Anweisungen Seite 6

9
MENU
The menu includes options as follows:
Operating mode
Image calibration
Video output
Clock setup
Defective pixel repair
Brightness setting of menu icons
Operating mode
There are three automatic operating modes:
"City" (enhanced contrast), "Forest" (low contrast) and
"Identification" (improved detail rendering).
Each mode includes optimal combination of parameters (brightness,
contrast, gain etc.) to deliver best possible image in specific viewing
conditions.
Press and hold the controller for two seconds to enter the menu.
Rotate the controller to select Mode option. Press the controller.
Rotate the controller to select icon
or (mode "Forest") or
Press the controller to confirm.
Icon of the selected mode is shown on the data panel in the lower
portion of the display.
Image calibration
Detailed description can be found in the section "
calibration " in the section 8 "Operation".
Selection/disable of video output signal
Press and hold the controller for two seconds to enter the menu.
Rotate the controller to select icon
Rotate the controller to select video output signal – PAL or NTSC
(video output is deactivated by default).
To disable the video output, select "OFF". Disabled video output
reduces power consumption of the thermal imager.
To exit the main menu, keep the controller pressed for two seconds or
wait 10 seconds to exit automatically.
Clock Set Up
Press and hold the controller for two seconds to enter the menu.
Rotate the contoller to select icon
Move the cursor by rotating the controller to select time format "24"
or "AM/PM".
Press the controller to proceed to hour setup. Set the hour by rotating
the controller.
Press the controller to proceed to minute setup. Set the minute by
rotating the controller.
To exit main menu, press and hold the controller for two second. Or
wait 10 seconds to exit automatically.
8
(mode "City")
(mode "Identification").
Switching on and
. Press the controller.
. Press the controller.
Defective pixel repair
When operating the thermal imager, there is a possibility of defective
(dead) pixels (bright or dark dots with constant brightness) appearing
on the dectector which are visible on the image.
Thermal imagers Quantum S provide an opportunity to repair defective
pixels on the detector using a software-based method.
Press and hold the controller for two seconds to enter the menu.
Rotate the controller to select icon
Select icon in the pop-up submenu and press the controller.
A red cross appears in the centre of display, coordinates (X;Y)
the cross relative to the centre of display appear in the place of pop-up
icons, icons disappear.
Rotate the controller to align the cross with a defective pixel (defective
pixel should go out).
Switch direction of the cross from horizontal to vertical by a short press
of the controller.
After the centre of the cross is aligned with a defective pixel, press
the (3) button to repair the pixel.
In case of success a short "OK" message appears in the place of the
coordinates.
Further on, move the cross to repair another defective pixel. When
moving the cross to the coordinates area, the latter goes to the lower
right portion of the display.
Return to default defective pixel pattern.
If you wish to return to the default defective pixel pattern
(i.e. restore all defective pixels previously repaired), select icon
pop-up submenu and press the controller.
Options "Yes" and "No" appear on the right of the icon.
Rotate the controller to select "Yes" and press the controller.
If you choose not to return to default pixel pattern, select "No" and
press the controller.
To exit the main menu, keep the controller pressed for two seconds or
wait 10 seconds to exit automatically.
Attention! One or two pixels in the form of bright white or colour
(blue, red) 1-2 pixels dots are allowed on the display of thermal
imager. These pixels cannot be repaired and are not a defect.
Brightness setting of menu icons
Press and hold the controller for two seconds to enter the menu.
Rotate the controller to select icon
Rotate the controller to select brightness level (1 to 10) of menu
icons.
To exit the main menu, keep the controller pressed for two seconds or
wait 10 seconds to exit automatically.
and press the controller.
X=50 of
Y=50
in the
. Press the controller.
9