Werbung
Verfügbare Sprachen
Verfügbare Sprachen
•
Do not use the blender without ingredients!
•
Place the mixing container on a stable and solid surface dur-
ing filling. In this way it is easier to attach the lid.
•
Do not exceed the maximum capacity (1500 ml) as indicated
on the mixing container!
•
Adjust the capacity to accommodate any frothing of the mix-
ture. If necessary, reduce the capacity.
•
Attach the lid in such way that the round tab seals the spout
of the mixing container.
•
Only take the appliance into operation after attaching lid and
fastening the stopper!
•
Do not remove the lid during operations! Wait until the knife
has come a complete stop before opening the lid.
Mixing Container Assembly
Please refer to our overviews on Page 3 and 4.
Check the pre-assembly! The sealing ring (27), the knife block (28)
and the screw-on base (29) must be assembled in the correct
sequence.
CAUTION:
•
The stud on the knife block must fit in the recess of the
screw-on base.
•
Never forget to place the sealing ring on the knife assembly;
otherwise the mixing container will leak.
•
Do not attach the threaded coupling askew.
Preparation
1. Attach the bowl and splash guard lid as described under "The
kneading machine"
"Assembly and operation", points 1, 2,
5 and 7.
2. Remove the safety cover (3) from the drive shaft of the blend-
er motor: Push and slide at the same time on the grooved
area.
3. Cut all ingredients in small pieces.
4. Fill the ingredients into the mixing container. Observe the
maximum capacity.
5. Press the lid (25) down on the mixing container. The mixing
container must be perfectly sealed.
6. Close the lid with the stopper (24). Use the recesses on the
cap to help you. Fasten the cap by turning it clockwise.
Blender Assembly And Operation
7. Place the mixing container on the mixing drive shaft. Attach
the blender jug with the arrow
appliance. Turn the blender jug clockwise as far as it will go.
The two arrows
and
must lie opposite one another.
8. Connect the mains cable to a properly installed and earthed
wall outlet.
9. Switch the appliance on using the POWER
10. Select a speed with the
/
11. Start operation with the POWER
NOTE:
If you start using the appliance immediately after connecting to
the mains, the appliance starts at speed setting 1.
over the dot on the base
button.
buttons.
button.
Refill Ingredients
•
Switch the appliance off.
•
Fill in ingredients or spices through the stopper opening.
•
Close lid and stopper opening again.
•
Continue operation.
Stop Operation
1. Switch the appliance off. Wait until the knife comes to a com-
plete stop.
2. Disconnect from mains power supply.
3. Detach the blender jug from the motor part by turning it anti-
clockwise.
4. Remove the lid before pouring out the contents.
5. Clean all used parts as described under "Cleaning".
6. Cover the mixing drive shaft with the safety cover (3).
IMPORTANT NOTE:
Do not store citrus juices or acidic foodstuffs in metal containers.
The mincer
WARNING:
•
When cleaning and assembling the mincer, handle the knife
(35) with the necessary care!
•
Always use the pusher to fill the mincer (30). Use only the
pusher to fill the mincer.
Preparation
Please also refer to our overviews on page 3 and 5.
1. Attach the bowl and the splash guard lid as described under
"The kneading machine"
1, 2, 5 and 7.
2. The access to the worm housing is protected by a cover (13)
on the appliance. Turn the cover clockwise to remove it.
3. Push the silicone coupling (34) onto the worm shaft (33).
4. Set the worm, sprocket first, into the horizontal section of the
worm housing.
Assembly of the accessories is described the following sections.
Prepare the mincer according to your requirements.
Assembling the mincer (see Fig. D)
NOTE:
•
Check any pre-assembly work!
•
Depending on how fine you want to mince, select a finer or
a courser mincing plate.
•
Lightly coat the mincing plate beforehand with sunflower oil.
Proceed as described under "Preparation".
5. Set the knife (35) onto the shaft of the worm with the sharp
side facing outwards.
6. Select a mincing plate (36). Use the recesses on the plate to
insert it into the worm housing.
More details can be found under "Attach preassembled worm
housing".
"Assembly and operation", points
55
Werbung
Kapitel
Fehlerbehebung
