Technical Data; Circular Saw Safety Warnings - Milwaukee M18 FPS55 Originalbetriebsanleitung

max.
59 mm
30

TECHNICAL DATA

Type
Production code
Battery voltage
No-load speed
Saw blade dia. x hole dia.
Saw blade thickness
Plate / Kerf
Riving Knife Thickness
Blade teeth
Bevel scale
Max. Cutting depth at 0° / 45°
With Guiderail
Without Guiderail
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 12,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Noise information: Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are::
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
Vibration information: Vibration total values (triaxial vector sum) determined
according to EN 62841
Vibration emission value a
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
> 59 mm
illustrations and specifications provided with this power tool. Failure
to follow all instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.

CIRCULAR SAW SAFETY WARNINGS

Cutting procedures
a)
blade. Keep your second hand on auxiliary handle, or motor
housing. If both hands are holding the saw, they cannot be cut by
the blade.
b) Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpiece.
Less than a full tooth of the blade teeth should be visible below the
workpiece.
d) Never hold the workpiece in your hands or across your leg
while cutting. Secure the workpiece to a stable platform. It is
important to support the work properly to minimise body exposure,
blade binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Contact with a ˝live˝ wire will also make
exposed metal parts of the power tool ˝live˝ and could give the
operator an electric shock.
/ Uncertainty K=
h
Sawing of wood
WARNING!
WARNING!
Read all safety warnings, instructions,
DANGER: Keep hands away from cutting area and the
M18 FPS55
Circular saw
4835 92 01 XXXXXX MJJJJ
18 V
2500 - 5600 min
165 x 20 mm
1,0 / 1,6 mm
1,4 mm
40
-1° - 48°
54 / 42 mm
59 / 44 mm
4,48 ... 5,54 kg
-18 ... +50 °C
M18B...; M18HB...
M12-18...; M1418C6
92,4 dB (A) / 3 dB (A)
103,4 dB (A) / 3 dB (A)
0,56 m/s / 1,5 m/s
2
f) When ripping, always use a rip fence or straight edge guide.
This improves the accuracy of cut and reduces the chance of blade
binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run off-centre, causing loss of
control.
h) Never use damaged or incorrect blade washers or bolt. The
blade washers and bolt were specially designed for your saw, for
optimum performance and safety of operation.
i) Always have the viewing window or splinter guard in place
during use.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, jammed or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
– when the blade is pinched or jammed tightly by the kerf closing
down, the blade stalls and the motor reaction drives the unit rapidly
back toward the operator;
– if the blade becomes twisted or misaligned in the cut, the teeth at
the back edge of the blade can dig into the top surface of the wood
causing the blade to climb out of the kerf and jump back toward the
operator.
Kickback is the result of saw misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
ENGLISH
-1
2
31