AEG X Flexibility CX7-2-35TM Gebrauchsanweisung Seite 5

ENGLISH
Thank you for choosing an AEG CX7 vacuum cleaner. In order to ensure the
best results, always use original AEG accessories and spare parts. They have
been designed especially for your vacuum cleaner. This product is designed
with the environment in mind. All plastic parts are marked for recycling
purposes.
DESCRIPTION OF CX7
A. ON/OFF button
B. Power regulation button
C. ON/OFF button, hand unit
D. Locking screw
E. Release button, hand unit
F. Charging station, wall unit
G. Charging station, oor unit
H. Charging adapter
I. Fine lter (inner lter)
J. Pre lter (outer lter)
K. Release button, dust container
L. Dust container
BEFORE STARTING
Check that the package includes all parts described in this instruction
manual and read this manual carefully. Pay special attention to the safety
precautions chapter. Save these instructions.
1
Assemble the handle.
2
Assemble the charge stand.
3
There is a hollow space in the bottom of the charging station where
unused cable can be wound. Insert the adaptor into the mains and
position the charging station on a stable and horizontal surface away
from heat sources, direct sunlight or wet places.
4
The charging indicator will be lit when CX7 is placed in the charging
station.
CHARGING CX7
5
When fully charged, the charging indicator will blink slowly. The
numbers of LED lamps will indicate the level of charge. Full charging
time is around 4 hours. For better battery performance, charge CX7 for
24 hours before rst use and always keep it on charge when not used.
VACUUMING WITH CX7
Before vacuuming, check that the nozzle wheels and the brush roll are
clean from sharp objects in order to avoid scratching sensitive oors
and to ensure full cleaning performance.
6
Start and stop CX7 by pushing the ON/OFF button.
CX7 will start on the high power mode.
For more silent cleaning and longer runtime, press the power regula-
tion button.
VACUUMING FURNITURE, CAR SEATS ETC.
7
Press the button to release the hand unit from the main body.
8
Attach the crevice nozzle to facilitate cleaning of areas di cult to reach.
Attach the brush on the crevice nozzle for dusting.
9
The crevice nozzle and small brush can be stored in the charging sta-
tion or in the slot on the back side of the handle.
BRUSHROLLCLEAN® FUNCTION (CERTAIN MODELS ONLY)
Use the BRUSHROLLCLEAN® function to keep the brush roll clean and
free from hair and bres. For best results use the BRUSHROLLCLEAN®
function when CX7 is fully charged.
10
Place CX7 on a hard and at surface. Do not use the BRUSHROLLCLEAN ®
function on carpets.
Press the BRUSHROLLCLEAN ® pedal with your foot while the cleaner is
on. Hold for 5 seconds until hairs and bres are removed. There will be
a cutting noise during this process, this is normal. If hairs remain on the
brush roll, repeat the process.
The BRUSHROLLCLEAN ® function is equipped with an overheating
protection. If the BRUSHROLLCLEAN ® function has been used for more
than 30 seconds (constant or interrupted) it will deactivate the brush
roll and turn o the nozzle front lights. The vacuum cleaner can still
be used, even when the BRUSHROLLCLEAN
To reactivate the BRUSHROLLCLEAN ® function, place CX7 on charge
and charge for 15 minutes.
Please note that the BRUSHROLLCLEAN® function might not be able to
www.aeg.com
M. Dusting brush
N. Crevice nozzle
O. Cable protector grill
P. Hatch cover for brush roll
Q. Brush roll
R. BRUSHROLLCLEAN® pedal*
S. Nozzle front lights
T. Charging indicator
U. Cli hanger
V. Slot for accessory storage
* Not on models CX7-2-30xxx
function is deactivated.
®
remove thicker threads or wires that are caught in the brush roll.
EMPTYING OF THE DUST CONTAINER
11
Remove the dust container by pressing the buttons.
12
Take out the lters from the dust container by pressing the release but-
tons. Empty the contents into a dustbin. Never wash the dust container
or lters in a dishwasher.
IMPORTANT FILTER CLEANING!
13
The lters must be cleaned at regular intervals to ensure a high clean-
ing performance. Take out the lters by pressing the release buttons.
Separate the inner lter from the outer lter.
14
Rinse the lter parts carefully under lukewarm water without using any
detergents. (Never use the dishwasher or washing machine.) S hake to
remove excess water and leave to dry minimum 12h before putting
them back into the cleaner.
CLEANING THE HOSE AND NOZZLE WHEELS
15
Loosen the hose behind the nozzle from its upper connection. Remove
any object or debris that can be blocking the air ow in the hose or in
the air channel to the dust cup, and put the hose back.
16
If the wheels need to be cleaned or get jammed, remove them carefully
by using a at screwdriver.
REMOVING AND CLEANING THE BRUSH ROLL
17
If the brushroll gets blocked CX7 will stop. Open the cable protector
grill and the brush roll hatch cover and remove the brush roll.
18
Us e a pair of scissors to remove threads etc. Reassemble the brush roll,
making sure it can spin freely.
REMOVING THE BATTERIES FOR RECYCLING
Warning; Battery removal must only be done by an AEG service
center or o cial collection point!
19
Only remove batteries if the product is to be scrapped. Improper han-
dling of the batteries may be hazardous. Batteries should always be
completely discharged before removal. Take your product to an AEG
service center or o cial collection point for recycling. They can remove
and recycle the battery and electric parts in a safe and professional way.
Follow your country's rules for collection of rechargeable batteries and
electrical products.
Enjoy a great cleaning experience with CX7!
DE
GB
EL
ES
FR
IT
NL
PT
AR
FA
7