DeWalt DCF835 Bersetzt Von Den Originalanweisungen Seite 34

EnGLIsh
Place the forward/reverse button
position or remove battery pack before changing accessories.
To install an accessory, push accessory to fully insert into
chuck. The chuck collar does not need to be pulled up to lock
accessory in place.
To remove an accessory, pull the chuck collar away from the
front of the tool. Remove the accessory and release the collar.
Anvil with Detent Pin (Fig. A)
DCF830, DCF880

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it contains
no cracks.

CAUTION: Inspect anvils and detent pins prior to use.
Missing or damaged items should be replaced before use.
Place the switch in the locked off (center) position or remove
battery pack before changing accessories.
To install an accessory on the anvil, align the hole in the side of
the accessory with the detent pin
the accessory on until the detent pin engages in the hole.
Depression of detent pin may be necessary to aid installation
of accessory.
To remove an accessory, depress the detent pin through the
hole and pull the accessory off.
Usage
Your impact tool generates the following maximum torque:
Cat # Ft.-Lbs.
DCF830 135
DCF835 111
DCF880 150
DCF885 114

CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Release the switch to stop
operation. Always check torque with a torque wrench, as
the fastening torque is affected by many factors including
the following:
ʵ Voltage: Low voltage, due to a nearly discharged battery,
will reduce fastening torque.
ʵ Accessory size: Failure to use the correct accessory size
will cause a reduction in fastening torque.
ʵ Bolt Size: Larger bolt diameters generally require higher
fastening torque. Fastening torque will also vary according
to length, grade, and torque coefficient.
ʵ Bolt: Ensure that all threads are free of rust and other
debris to allow proper fastening torque.
ʵ Material: The type of material and surface finish of the
material will affect fastening torque.
32
in the locked off (center)
2
13 on the anvil 12 . Press
In.-Lbs. Nm
1620 185
1330 150
1800 203
1400 155
ʵ Fastening Time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recom mended could cause the fasteners to be
overstressed, stripped or damaged.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessories prior to use to ensure that they con tain
no cracks
Consult your dealer for further information on the
appropriate accessories.
WALT recommended
e