Makita DCU180ZX1 Betriebsanleitung Seite 16

6. As the view is obscured on slopes, keep the
height of the load to a minimum.
7. Never park the machine on steep slopes. Park
the machine on flat ground, pull the brake
lever and lock the brake, and then turn the
power off.
8. Do not change the direction or speed mode on
steep slopes.
9. Do not release the switch trigger on upward
slopes. The machine may go in reverse and
cause an accident.
10. Make sure that the remaining battery capacity
is enough before operating on slopes. If the
remaining battery capacity is not enough, charge
the battery or replace it with a charged one.
Loading objects
1. Do not overload objects. When loading
objects, be sure to follow the instructions and
load limits in the manual.
2. Firmly secure the objects with ropes.
Load the objects within the carrier or bucket.
3.
If the objects protrude from the carrier or bucket,
there is a risk of accidents due to the objects
falling or contact obstacles such as walls.
4. Be sure that loaded objects are below eye
level. If the load is too high, it is dangerous
because the view is obscured. Also, there is a risk
of overturning and injury because the load is likely
to be unbalanced.
5. Load the objects on the carrier or bucket
evenly. If the objects are loaded unevenly, there is
a risk of overturning and injury because the load is
likely to be unbalanced.
6. Before loading the objects or operating the
machine, make sure that the lock lever is fully
pulled down and completely locked.
7. Be sure to load heavy objects first to keep
balance.
8. Do not extend the front and side rails on steep
slopes. Extend the side rails when lightweight
objects are loaded.
9. When extending the front and side rails, do not
extend them over the extension limit. Be sure
to extend the side rails so that the right and
left sides are the same length, and load objects
evenly.
10. Load and unload objects on flat ground.
11. When lifting and tilting the carrier or bucket,
hold the handles and frame firmly, and work in
a stable posture.
Maintenance
1. Always be sure to park the machine on flat
ground and lock the brake lever before stor-
age or attempting to perform inspections or
maintenance.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
Do not disassemble or tamper with the battery
2.
cartridge. It may result in a fire, excessive heat,
or explosion.
If operating time has become excessively
3.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them
4.
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
Do not short the battery cartridge:
5.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
fire, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
When disposing the battery cartridge, remove
11.
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
16 ENGLISH