How To Change The Activated Carbon Lter; Rating Plate; Operation And Handing; Operating Elements - CASO DESIGN WineDeluxe WD 24 Original Bedienungsanleitung

4.11 How to change the activated carbon fi lter
Replace the activated carbon fi lter (Caso Item No. 692) once a year.
1.
To do this, remove the bottles which are in front of the fi lter.
2.
To replace the existing fi lter, pull it out and insert a new one.

4.12 Rating plate

The rating plate with the connection and performance data can
be founded on the back of the device.

5 Operation and Handing

This chapter provides you with important notices with regard to
operating the device.

5.1 Operating elements

1 2 3 4
1
Increase temperature
(upper Zone)
2 Decrease temperature
(upper Zone)
3
Display (upper Zone)
4 Increase temperature
(lower Zone)

5.1.1 Symbols shown on the control panel

ECO mode is active
Unit reduces the temperature: The symbol goes out as
soon as the unit has reached the set temperature.
Unit increases the temperature: The symbol goes out as
soon as the unit has reached the set temperature.
Door is closed
Temperature display in °C
Temperature display in °F
5 6 7 8
5
Decrease temperature
(lower Zone)
6
Display (lower Zone)
7
Light control
8
On / Off

5.2 Operation of the appliance

PLEASE NOTE

Due to the appliance's 2-zone cooling and ventilation system,
temperature settings for each zone are independent of the
other zone.

This means that the temperature of the lower zone cannot be
set below that of the upper zone.

When using both zones with diff erent storage temperatures
the temperature in the upper zone can thus only be lower or
the same as the temperature in the lower zone.

A large diff erence in the temperature settings for each zone
can result in higher energy consumption.
5.2.1 Switching on and off
1.
Plug the power socket into mains power.
2.
The On / Off button fl ashes.
3.
Press the On / Off button.
4. The last selected temperature will be shown on the control
panel.
5.
To switch the appliance off , press the On / Off button until
the symbols on the control panel disappear.

5.2.2 Setting the temperature

1.
Turn the appliance on.
2.
The last selected temperature will be shown on the control
panel.
3. By pressing the two left arrow keys simultaneously, you can
switch between the temperature display in °C and °F.
4.
The selected temperature unit is saved when the corre-
sponding symbol on the control panel stops fl ashing and is
permanently on.
5.
Use the arrow buttons to set the temperature in 1° incre-
ments from 5 °C to 20 °C (41 °F to 68 °F).
6.
The desired temperature will be stored approx. 5 seconds
after the last time you press a button and the symbol on the
control panel stops fl ashing and is permanently on.
7.
The appliance's current temperature is shown.
PLEASE NOTE

Temperature recommendations: Red wine: 12°C – 18°C and
white wine: 6°C – 10°C.

The appliance can achieve the best cooling and consumption
results at a recommended ambient temperature of 16 - 20 °C.

The temperature in the appliance depends on the ambient
temperature, the quantity of bottles and the chosen tempe-
rature.

Please note that your appliance is intended to cool wine.
The maximum temperature which can be achieved inside
the cooler should NOT signifi cantly exceed the ambient
temperature in the room.

5.3 Illumination

5.3.1 Setting the "ECO" mode

If you select the "ECO" mode, then the appliance's interior light
will turn off when the door is shut.
1.
Press the "Light" button.
2.
The "ECO" symbol will appear on the control panel display.
3. Shut the door.
4.
The LED light will turn off . Next time you open the door, the
light will turn on again.
5.
To deactivate the "ECO" mode, press the "Light" button
again. The LED strips will be permanently on, also when the
door is closed.
PLEASE NOTE

The illumination will switch off after 4 hours to save energy.
CASO WineDeluxe WD 24
DE
EN
FR
IT
ES
NL
RUS
SE
PT
29