Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ACTIVATING/DEACTIVATING COOKING ZONES AND ADJUSTING
POWER
To activate the cooking zones:
1.
Switch on the hob. If a recipient is already in place, the hob automatically
detects it. Select the suggested zone to choose the power.
2.
Place the pot in the chosen cooking zone, ensuring that it is covering
one or more of the reference points on the surface of the hob.
* Using this position will allow you to benefit from maximum power output.
Please note: Do not cover the display or the slide touchscreen with accessories.
If a utensil is covering one of the displays, the hob may not function properly.
On the right display, the message "CHECK TOUCH AREA, remove the object
within one minute" will appear. Remove the object and wait until the
message disappears. If the problem persists, disconnect and reconnect the
power to the cooktop.
In the cooking zones close to the control panel, it is advisable to keep pots
and pans inside the markings (taking both the bottom of the pan and the
upper edge into consideration, as this tends to be larger).
This prevents excessive overheating of the touchpad. When grilling or frying,
please use the rear cooking zones wherever possible.
3.
Select the cooking zone or flexible area from the left-hand display.
4.
Set the desired power level by pressing or moving your finger
horizontally across the slide touchscreen.
The power level set will appear in the pane of the cooking zone selected.
Each cooking zone offers a range of different heat settings, from "1"
(minimum power) to "18" (maximum power).
Using the slide touchscreen, you can also select the quick heat function,
which will appear on the display with the letter "P".
Please note: The cooking zone pane will flash, if the pot is not suitable for
induction cooking, is not positioned correctly or is not of an appropriate size.
If no pot is detected within 30 seconds of making the selection, the cooking
zone switches off.
To deactivate the cooking zones:
Select the cooking zone in the left-hand display and press the "OFF" button
at the top of the slide touchscreen. If the cooking zone is still hot, the
residual heat indicator "H" will appear in the corresponding pane.
H
ADD POT
When using a cooking area composed of several zones, the pot can be
placed anywhere on the active area. The hob will automatically recognise
the actual positioning of the pot.
If you wish to add an additional pot to the active cooking area, use the "Add
pot"
command to allow the hob to detect the new pot.
KEY LOCK
To prevent accidental activation of the hob during cleaning, or to prevent
the controls from being changed accidentally whilst cooking, press the
"Key lock"
button for 3 seconds: a beep and a warning light indicate
that this function has been activated.
The control panel will be locked, with the exception of the off button.
To reactivate the controls, press the "Key Lock"
seconds. The warning light switches off and the hob is active again.
TIMER
When the hob is in stand-by mode (no cooking zones are being used), you
can use the right-hand display as a timer.
To activate the timer:
1.
Switch on the hob.
2.
Press the hourglass icon
display.
3.
Use the "+"/"–" buttons to set the time.
4.
When the set time has elapsed, an acoustic signal sounds.
To change or deactivate the timer:
1.
Press the hourglass icon
display.
2.
Use the "+" and "–" buttons to reset the desired time, or press the
"STOP" button to turn off the timer.
SETTING THE COOKING TIME
The cooking zones can be programmed to switch off automatically.
To set the cooking time:
1.
Select the cooking zone and set the required power level.
2.
Press the stopwatch icon
display.
3.
Use the "+"/"–" buttons to set the time.
4.
Once the set time has elapsed, an acoustic signal sounds and the
cooking zone switches off automatically.
To change or deactivate the cooking timer:
1.
Select the active cooking zone.
2.
Press the stopwatch icon
display.
3.
Use the "+" and "–" buttons to reset the desired time, or press the
"STOP" button to cancel the set cooking time.
A cooking time can be set for each zone or flexible area by following the
same steps.
– 10 –
button again for 3
that appears on the manage functions
that appears on the manage functions
that appears on the manage functions
that appears on the manage functions
Werbung
Inhaltsverzeichnis
