Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4.11 Starting the programme
1. Press Start / Pause button to start the programme.
2. Programme follow-up light showing the startup of the
programme will turn on.
C
If no programme is started or no button is pressed within
1 minute during programme selection process, the
machine will switch to Pause mode and the illumination
level of the temperature, speed and loading door indicator
lights will dim. Other indicator lights and indicators will
turn off. Once the Programme Selection knob is rotated or
any button is pressed, indicator lights and indicators will
turn on again.
4.12 Child Lock
Use Child Lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
C
If the Programme Selection knob is turned when the Child
Lock is active, "Con" appears on the display. The Child
Lock does not allow any change in the programmes and
the selected temperature, speed and auxiliary functions.
Even if another programme is selected with the
Programme Selection knob while the Child Lock is active,
previously selected programme will continue running.
To activate the Child Lock:
1. and 2. Auxiliary Function buttons are pressed and held for
3 seconds. The lights on the 1
buttons will flash, and "C03", "C02", "C01" will appear on
the display respectively while you keep the buttons pressed
for 3 seconds. Then, "Con" will appear on the display
indicating that the Child Lock is activated. If you press any
button or turn the Programme Selection knob when the Child
Lock is active, same phrase will appear on the display. The
lights on the 1st and 2nd auxiliary function buttons that are
used to deactivate the Child Lock will blink 3 times.
To deactivate the Child Lock:
Press and hold 1
and 2
auxiliary function buttons for 3
st
nd
seconds while any programme is running. The lights on the
1
and 2
Auxiliary Function buttons will flash, and "C03",
st
nd
"C02", "C01" will appear on the display respectively while
you keep the buttons pressed for 3 seconds. Then, "COFF"
will appear on the display indicating that the Child Lock is
deactivated.
C
In addition to the method above, to deactivate the Child
Lock, switch the Programme Selection knob to On /
Off position when no programme is running, and select
another programme.
Child Lock is not deactivated after power failures or
when the machine is unplugged.
4.13 Progress of programme
Progress of a running programme can be followed from the
Programme Follow-up indicator. At the beginning of every
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programme step. If the change is not compatible, relevant
lights will flash for 3 times.
38 / EN
and 2
Auxiliary Function
st
nd
C
If the machine does not pass to the spinning step, Rinse
Hold function might be active or the automatic unbalanced
load detection system might be activated due to the
unbalanced distribution of the laundry in the machine.
4.14 Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases when
the water level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door light
illuminates steadily within 1-2 minutes and the loading door
can be opened.
If the level is unsuitable, Loading Door light turns off and the
loading door cannot be opened. If you are obliged to open
the Loading Door while the Loading Door light is off, you
have to cancel the current programme; see "Canceling the
programme".
4.15 Changing the selections after programme
has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to
pause mode while a programme is running. The light of
the step which the machine is in starts flashing in the
Programme Follow-up indicator to show that the machine
has been switched to the pause mode.
Also, when the loading door is ready to be opened, Loading
Door light will also illuminate continuously in addition to the
programme step light.
Changing the auxiliary function, speed and
temperature
Depending on the step the programme has reached, you
can cancel or activate the auxiliary functions; see, "Auxiliary
function selection".
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
C
If no change is allowed, the relevant light will flash for 3
times.
Adding or taking out laundry
1. Press Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the
relevant step during which the machine was switched into
the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
4. Close the Loading Door.
5. Make changes in auxiliary functions, temperature and
speed settings if necessary.
6. Press Start / Pause button to start the machine.
4.16 Cancelling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be cancelled. End / Cancel light will flash continuously to
notify that the programme has been canceled.
Pump function is activated for 1-2 minutes regardless of the
programme step, and whether there is water in the machine
or not. After this period, your machine will be ready to start
with the first step of the new programme.
Washing Machine / User's Manual
Werbung
Inhaltsverzeichnis
