Technical Data; Before Starting The Equipment - EINHELL 42.579.40 Originalbetriebsanleitung

4. Technical data

Mains voltage: ............................... 230 V ~ 50 Hz
Power input: ............................................ 1250 W
Idling speed: ........................................ 0-850 rpm
Blow rate: .......................................... 0-4100 rpm
Drilling capacity in concrete/stone (max.): 32 mm
Protection class: ............................................ II/
Weight: .......................................................5.7 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 92.5 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ...................... 103.5 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The hammer drill is not designed for outdoors
use as specifi ed I Article 3 of Directive 2000/14/
EC_2005/88/EC.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Hammer drilling in concrete
Vibration emission value a
K uncertainty = 1.5 m/s
Chiseling
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_TE_RH_32_E_SPK9.indb 15 Anl_TE_RH_32_E_SPK9.indb 15
= 17.918 m/s
2
h
2
= 14.173 m/s
2
h
2
- 15 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Check the drilling point for concealed electrical
cables, gas and water pipes using a cable/pipe
detector.
5.1 Additional handle (Fig. 2 – Item 6)
For safety reasons you must only use the
hammer drill with the additional handle.
The additional handle (6) enables you to achieve
better stability whilst using the hammer drill. The
machine must not be used without the additional
handle (6) for safety reasons.
The additional handle (6) is secured to the
hammer drill by a clamp. Turning the handle anti-
clockwise (looking from the handle) will release
the clamp. Turning the handle clockwise will tigh-
ten the clamp.
First release the additional handle clamp. You can
07.11.2022 09:10:49 07.11.2022 09:10:49