Additional Safety Rules For Tool - Makita BTW121 Betriebsanleitung

ADDITIONAL SAFETY RULES FOR TOOL

1. Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will also make exposed metal parts of the
tool "live" and shock the operator.
3. Wear ear protectors.
4. Check the socket carefully for wear, cracks or
damage before installation.
5. Hold the tool firmly.
6. Always be sure you have a firm footing.
7. Be sure no one is below when using the tool in
high locations.
8. The proper fastening torque may differ depend-
ing upon the kind or size of the bolt. Check the
torque with a torque wrench.
SAVE THESE INSTRUCTIONS.
Charging (Fig. 2)
1. Plug the battery charger into the proper A/C voltage source. Two charging lights will flash in green color repeat-
edly.
2. Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger
can be opened with inserting and closed with pulling out the battery cartridge.
3. When the battery cartridge is inserted, the charging light color will change from green to red and charging will
begin. The charging light will keep lighting up lit steadily during charging. One red charging light indicates charged
condition in 0 – 80% and two red ones indicates 80 – 100%.
4. With finish of charge, the charging lights will change from two red ones to two green ones.
5. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its
"trickle charge (maintenance charge)" mode which will last approximately 24 hours.
6. After charging, unplug the charger from the power source. Refer to the table below for the charging time.
Battery type
BH1220
BH1233
NOTE:
• The battery charger is for charging Makita-battery car-
tridge. Never use it for other purposes or for other man-
ufacturer's batteries.
• When you charge a new battery cartridge or a battery
cartridge which has not been used for a long period of
time, it may not accept a full charge. This is a normal
condition and does not indicate a problem. You can
recharge the battery cartridge fully after discharging it
completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated
tool or battery cartridge which has been left in a loca-
tion exposed to direct sunlight for a long time, the
charging light may flash in red color. If this occurs, wait
for a while. Charging will begin after the battery car-
tridge is cooled by the cooling fan installed in the
charger. When the temperature on battery is more than
approx. 70°C, two charging lights may flash in red
color, and when approx. 50°C – 70°C, one charging
light in red color.
• If the charging light flashes alternately in green and red
color, charging is not possible. The terminals on the
charger or battery cartridge are clogged with dust or
the battery cartridge is worn out or damaged.
ENB025-1
Capacity (mAh)
2,000
3,300
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while sliding the button on the side of the cartridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red part on
the upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not, it
may accidentally fall out of the tool, causing injury to
you or someone around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Number of cells
10
10
Cooling system
• This charger is equipped with cooling fan for heated
battery in order to enable the battery to prove its own
performance. Sound of cooling air comes out during
cooling, which means no trouble on the charger.
• Yellow light will flash for warning in the following cases.
– Trouble on cooling fan
– Incomplete cool down of battery, such as, being
clogged with dust
The battery can be charged in spite of the yellow warn-
ing light. But the charging time will be longer than usual
in this case.
• Check the sound of cooling fan, vent on the charger
and battery, which can be sometime clogged with dust.
• The cooling system is in order although no sound of
cooling fan comes out, if the yellow warning light will
not flash.
• Always keep clean the vent on charger and battery for
cooling.
• The products should be sent to repair or maintenance,
if the yellow warning light will frequently flash.
Charging time
Approx. 30 min.
Approx. 50 min.
5