Maintenance - AEG K 55 Gebrauchsanweisung

TECHNICAL DATA
Nominal power output ..................................................................
No-load speed ..............................................................................
Speed under load max. ................................................................
Saw blade dia. x hole dia .............................................................
Cutting depth at 90° ......................................................................
Cutting depth at 45° ......................................................................
Weight without cable ....................................................................
Typical weighted acceleration in the hand-arm area ....................
Typical A-weighted sound levels:
Sound pressure level .................................................................
Sound power level .....................................................................
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Sawdust and splinters must not be removed while the
machine is running.
Never reach into the danger area of the plane when it is
running.
Before use check machine, cable, and plug for any
damages or material fatigue. Repairs should only be carried
out by authorised Service Agents.
Dust that arises when working in wood or using the tool on
industrial material can be dangerous to health. In this case
connect the tool to a suction device.
Always use the protective shields on the machine.
Do not use machines on any material containing asbestos.
Protective swing guard operation only with the provided
lever or automatically by the workpiece.
Before switching on ensure that protective swing guard
moves freely.
When plunge cutting secure the workpiece against kickback
(e.g. with cross bar).
Do not use saw blades not corresponding to the key data
given in these instructions for use.
Be careful not to saw into nails or similar objects.
The riving knife should be adjusted so that: the distance
between it and the tips of the saw blade teeth does not
exceed 5 mm, it is not more than 5 mm away from the
lowest point of the tips of the saw blade teeth
Do not use cracked or distorted saw blades or HSS saw
blades (high speed steel).
The teeth thickness, or the set of the teeth must be thicker
than the body of the blade and the riving knife. Do not
remove the riving knife (exception: plunge cutting).
Do not brake the speed of the saw-blade after switching off
the motor by pressing on it from the side.
Do not clamp the protective swing guard.
Clamp wooden rods on both sides of the saw blade to
prevent them from rotating.
Do not fix the on/off switch in the "on" position when using
the saw hand-held.
K 55 KS 55 S
........1010 W .............1010 W .............1500 W .............. 1400 W
........5800 /min ..........5800 /min ..........5200 /min ........... 5500 /min
........3900 /min ..........3900 /min ..........3800 /min ........... 3800 /min
....160x20 mm ....... 160x20 mm ....... 190x30 mm ........210x30 mm
........ 0-55 mm ........... 0-55 mm ............0-66 mm ............ 0-75 mm
........ 0-34 mm ........... 0-34 mm ............0-44 mm ............ 0-50 mm
...........4,2 kg ................4,2 kg ................5,6 kg ................. 6,0 kg
........< 2,5 m/s ..........< 2,5 m/s
2
............94 dB(A) ...........94 dB(A) ...........98 dB(A) ............ 97 dB(A)
..........107 dB(A) .........107 dB(A) ......... 111 dB(A) ...........110 dB(A)
SPECIFIED CONDITIONS OF USE
This electronic circular saw can cut lengthways and mitre
accurately in wood, plastic, and aluminium.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to safety
class II.
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected. If the system impedance of the power supply is
lower than 0,2 Ohm, disturbances are unlikely to occur.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at:
Max-Eyth-Straße 10, D-71364 Winnenden, Germany
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
KS 66 S
..........< 2,5 m/s .......... < 2,5 m/s
2 2
Volker Siegle
Manager Product Development
AEG Elektrowerkzeuge,
.
ENGLISH
HK 75 A
2
20