Technical Data; Noise/Vibration Information - Bosch GCM 8 SJL Professional Originalbetriebsanleitung

OBJ_BUCH-1736-004.book Page 25 Friday, May 22, 2015 10:12 AM
25 Mounting holes
26 Recessed handles
27 Adjustable fence
28 Locking screw of the adjustable fence
29 Material clamp
30 Stop for standard 45°, 22.5° and 33.9° bevel angles
31 Chip deflector
32 Depth stop
33 Locking screw for slide device
34 Tilt protector bar
35 Hex key (5 mm)
36 Mounting holes for material clamp
37 Material stop*
38 Transport safety-lock
39 Laser warning label
40 Laser on/off switch (for marking of cutting line)
41 Clamping lever for any bevel angle
42 Scale for bevel angle
43 Indicator for bevel angle
44 Stop for 0° standard bevel angle

Technical Data

Sliding Mitre Saw
Article number
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Weight according to EPTA-Procedure 01:2014
Protection class
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Permissible workpiece dimensions (maximum/minimum) see page 29.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 99 dB(A); Sound power level
112 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029-2-9: a
2
K=1,5 m/s .
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
Bosch Power Tools
45 Spindle lock
46 Hex socket screw for mounting of saw blade
47 Clamping flange
48 Interior clamping flange
49 Threaded rod
50 Screws for insert plate
51 Lock screw of the material stop*
52 Clamping screw of the material stop*
53 Adjustment screw for laser position
(parallelism)
54 Stop screw for 0° bevel angle
55 Screw for bevel angle indicator
56 Stop screw for 45° bevel angle
57 Set screws of scale 17 for mitre angles
58 Screw for mitre angle indicator
59 Velcro strap
60 Laser lens cover
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
3 601 M19 160
W
-1
min
nm
mW
kg
mm
mm
mm
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
2
=2,5 m/s ,
take into account the times when the tool is switched off or
h
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
3 601 M19 1P0
3 601 M19 190
1250 1400
5500 5500
 
650 650
< 0.39 < 0.39
1M 1M
17.3 17.3
/II /II
210–216 210–216
1.3–1.8 1.3–1.8
30 30
1 609 92A 1CK | (22.5.15)
English | 25
GCM 8 SJL
3 601 M19 1..
1600
5500

650
< 0.39
1M
17.3
/II
210–216
1.3–1.8
30