Mounting And Operation - Bosch AdvancedAquatak 140 Originalbetriebsanleitung

– Sound power level
– Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined
h
according to EN 60335-2-79
– Vibration emission value a
h
– Uncertainty K

Mounting and Operation

Action
Delivery scope
Adjusting the Handle
Connecting high pressure gun
to lance
Connecting high pressure wa-
ter supply hose/nozzle
Attaching Nozzle
Adjusting water jet
Connect detergent bottle
Connecting to the water supply
Switching On and Off
Clean the water filter
Clean nozzle
Gun storage
Gun/lance/nozzle stored during
work breaks
Storage
Selecting Accessories
Switching on
For Your Safety
Warning: Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Contact your Bosch Ser-
vice Centre for details. If in doubt contact a qualified electri-
cian or the nearest Bosch Service Centre.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
– 2.5 mm – max length 25 m
Note: If an extension cable is used it must be earthed and
connected through the plug to the earth cable of your supply
network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest
Bosch Service Centre.
Bosch Power Tools
Figure Page
and intended for outdoor use.
A 279
The connections (plugs and sockets) should be kept dry and
B 279
off the ground.
C 280
For increased electrical safety use a Residual Current Device
(RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
D 280
If the supply cord is damaged, it must be replaced by a
Bosch Service Centre.
E – F 281 - 282
For products not sold in GB:
Warning: For your safety, it is required that the plug at-
G 283
tached to the product is connected with the extension cord.
The coupling of the extension cord must be protected
H 284
against splash water, be made of rubber or coated with rub-
I 284
ber. The extension cord must be used with a cable strain re-
J 285
lief.
Products sold in GB only:
K 285
Your product is fitted with an BS 1363/A approved electric
L 286
plug with internal fuse (ASTA approved to BS 1362).
M 286
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
M 286
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
N 287
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Operation
To prevent damage to the appliance, do not allow it to
u
operate dry.
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
Autogoods "130"
3 600 HA7 D..
dB(A)
dB
2
m/s
2
m/s
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and
socket must be of watertight construction
F 016 L81 693 | (30.04.2019)
English | 17
91
= 3
0.5
= 0.5