Bosch GCM 10 GDJ Professional Originalbetriebsanleitung Seite 42

42 | English
Checking (see figure S1)
– Set an angle gauge to 45° and place it on the saw table
(33).
The leg of the angle gauge must be flush with the saw blade
(34) along its entire length.
Setting (see figure S2)
– Tighten or loosen the set screw (57) using a ratchet span-
ner (8 mm) until the leg of the angle gauge is flush with
the saw blade along its entire length.
– Retighten the clamping handle (13).
If the angle indicators (28) and (21) are not in line with the
45° marks on the scale (27) following adjustment, first
check the 0° setting for the bevel angle and the angle indicat-
ors once more. Then repeat the adjustment of the 45° bevel
angle.
Setting the Standard 45° Mitre Angle (right)
– Bring the power tool into the work position.
– Turn the saw table (33) to the 0° detent (14). The lever
(12) must be felt to engage in the detent.
– Pull the right-hand adjustable fence (7) all the way out.
– Loosen the clamping handle (13).
– Use the handle (3) to tilt the glide arm slightly to
the left from the 0° position and turn the rotary
knob (32) until the right-hand bevel angle range is
shown.
– Swivel the glide arm to the right stop (45°) by the handle
(3).
Checking (see figure T1)
– Set an angle gauge to 135° and place it on the saw table
(33).
The leg of the angle gauge must be flush with the saw blade
(34) along its entire length.
Setting (see figure T2)
– Tighten or loosen the set screw (58) using a ratchet span-
ner (8 mm) until the leg of the angle gauge is flush with
the saw blade along its entire length.
– Retighten the clamping handle (13).
If the angle indicators (28) and (21) are not in line with the
45° marks on the scale (27) following adjustment, first
check the 0° setting for the bevel angle and the angle indicat-
ors once more. Then repeat the adjustment of the 45° bevel
angle.
Aligning the scale for mitre angles
– Bring the power tool into the work position.
– Turn the saw table (33) to the 0° detent (14). The lever
(12) must be felt to engage in the detent.
Checking (see figure U1)
– Set an angle gauge to 90° and position it between the
fence (8) and the saw blade (34) on the saw table (33).
The leg of the angle gauge must be flush with the saw blade
(34) along its entire length.
Setting (see figure U2)
– Loosen all four set screws (59) using the hex key (4 mm)
(30) and turn the saw table (33) together with the scale
1 609 92A 6SR | (09.07.2021)
(31) until the leg of the angle gauge is flush with the saw
blade along its entire length.
– Re-tighten the screws again.
If the angle indicator (51) is not aligned with the 0° mark on
the scale (31) following adjustment, loosen the screw (60)
using a cross-headed screwdriver and align the angle indic-
ator along the 0° mark.
Adjusting the Clamping Force of the Clamping Handle
(13) (see figure V)
The clamping force of the clamping handle (13) can be ad-
justed.
Checking
– The clamping force of the clamping handle must hold the
glide arm securely in place at any bevel angle.
Setting
– Loosen the clamping handle (13).
– Use a socket spanner (17 mm) to turn the set screw (61)
anticlockwise to reduce the clamping force or clockwise
to increase the clamping force.
– Set a bevel angle, retighten the clamping handle (13) and
check whether the required clamping force has been
reached.
Transport (see figure W)
Before transporting the power tool, the following steps must
be carried out:
– Slide the glide arm (23) all the way back and secure it in
this position (see "Securing the glide arm", page 23).
– Make sure that the depth stop (25) is pressed all the way
in and that the adjusting screw (24) fits through the re-
cess without touching the depth stop when moving the
glide arm.
– Guide the glide arm downwards until you can press the
transport safety lock (26) all the way in
– Push the extension bar (16) in fully.
– Set the bevel angle to 0° and tighten the clamping handle
(13).
– Turn the saw table (33) as far as possible to the left and
tighten the locking knob (11).
– Wind up the mains cable and tie it together with the hook-
and-loop strap (62).
– Remove all accessories that cannot be securely fitted to
the power tool.
– If possible, transport unused saw blades in an enclosed
container.
– Carry the power tool by holding it by the recessed
handles (17) on the sides of the saw table.
Use only the transport fixtures to transport the power
u
tool. Never carry the power tool by the protective
devices, the glide arm (23) or the handle (3).
Bosch Power Tools