Before use
CAUTION! RISK OF INJURY!
►
Before any work on the appliance, disconnect the plug.
Risk of electric shock!
Motor unit
Attaching the round handle
♦
Place the round handle
in the desired position on the boom
♦
Tighten the screw
.
Fastening/attaching the shoulder strap
♦
Hook the shoulder strap
into the carrying lug
♦
Adjust the length of the shoulder strap
lug
is at hip height when the strap is hooked in place.
Assembling the hedge trimmer
♦
Push the front boom
of the hedge trimmer onto the boom
motor unit.
♦
The locking pin
must engage.
♦
Secure the two booms
the nut
on the opposite side.
Mounting the pole pruner
♦
Push the front boom
of the pole pruner to the boom
unit.
♦
The locking pin
must click into place.
♦
Secure the two booms
the nut
on the opposite side.
Swivelling of the hedge trimmer
♦
Trigger the lock/release
.
♦
Press the control lever
and swivel the hedge trimmer into the
desired position.
♦
Allow the control lever
and the lock/release
recess in the base plate (hedge trimmer)
Swivelling of the pole pruner
♦
Release the lock/release
.
♦
Press the control lever
and swivel the pole pruner into the desired
position.
♦
Allow the control lever
and the lock/release
recess in the base plate (pole pruner)
■
22
│
GB │ IE
.
to your size so that the carrying
with the tommy screw
; to do this, fit
of the motor
with the tommy screw
; to do this, fit
to click into the
.
to click into the
.
Mounting the saw chain and blade
WARNING!
►
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
NOTE
►
Pay close attention to the running direction of the saw chain
the blade
and at the sprocket cover
.
►
The blade
and the saw chain
delivery.
►
Depending on wear, the blade
♦
Undo the nut
using the assembly tool
♦
Remove the sprocket cover
♦
You may have to loosen the saw chain
and the saw chain
chain"). Follow these instructions in reverse order.
of the
♦
Remove the blade
(pole pruner)
.
♦
Reset the saw chain
♦
Lay the guide rail
roll pin
in the blade hole
over the chain sprocket
♦
Replace the sprocket cover
♦
Now you can tighten the saw chain
checking the saw chain").
Tightening and checking the saw chain
NOTE
►
The tension of the saw chain
function of the appliance. A correctly pre-stressed saw chain
increases the service life of your appliance.
WARNING!
►
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
♦
Loosen the nut
♦
Using the assembly tool
clockwise direction to increase the tension.
♦
Using the assembly tool
anticlockwise direction to decrease the tension.
♦
The saw chain
whether the saw chain
♦
Tighten the nut
NOTE
►
When pulling on the saw chain
the gap between the saw chain
than 2 mm.
►
A new saw chain
►
Check the chain tension before each use of the appliance.
.
are already assembled upon
can be turned.
.
.
to remove the blade
(see section "Tightening and checking the saw
with the saw chain
from the base plate
starting at the top of the blade
over the blade guide
, while inserting the chain
. At the same time, lay the saw chain
.
and tighten the nut
(see section "Tightening and
is important for your safety and the
a little using the assembly tool
, turn the chain adjuster screw
, turn the chain adjuster screw
must lie against the underside of the blade. Check
can be drawn over the blade
using the assembly tool
.
with a force of 9 N (approx. 1 kg),
and blade
should not be more
stretches and must be tightened more frequently.
PHSHE 900 B2
on
.
gently.
.
in a
in an
by hand.