Technical Data; Before Starting The Equipment; Operation - EINHELL GCH 2000 W Originalbetriebsanleitung

4. Technical data

Rated voltage: ............................... 230 V ~ 50 Hz
Heat output: ............................................ 2000 W
Thermostat control: ........................... 15°C -50°C
Protection class:.................................................. I
Equipment dimensions
without feet approx.: ..................86 x 10 x 46.5 cm
Equipment dimensions
with feet approx.: .......................86 x 23 x 52.5 cm

5. Before starting the equipment

5.1 Assembly
The equipment can be used indoors in a free
standing position or mounted on a wall. The
minimum clearances must be observed. The
equipment is allowed to be used only when it is
completely assembled and in a vertical position.
a) Free-standing installation (Fig. 3)
Ensure that a minimum distance of 30 cm to the
sides, 60 cm to the top and 100 cm to the front of
the equipment are maintained.
Observe point 1 - Safety information.
Important! To prevent damage when attaching the
feet to the heater, place the heater upside down
on a soft surface (e.g. a carpet).
Fit the two feet (8) to the housing (11), each with
four M4x10 screws (16).
b) Mounting on a wall (Fig. 4-5)
Important! Make sure that there are no electric
cables or other installations (for example water
pipes) near the drill holes. Ensure that the equip-
ment is secured fi rmly and horizontally to the wall.
Use only suitable fastening material on a wall
capable of bearing the load.
The supplied dowels and screws are suitable for
the following: Concrete, natural stone with a den-
se structure, solid brick, solid limestone bricks,
solid lightweight concrete bricks and aerated
concrete.
Ensure that a minimum distance of 30 cm to the
sides, 60 cm to the top, 30 cm to the bottom and
100 cm to the front of the equipment are main-
tained. The mounting height (upper edge of the
heater) must be less than 180 cm.
Observe point 1 - Safety information.
Anl_GCH_2000_SPK7.indb 16 Anl_GCH_2000_SPK7.indb 16
GB
•
Do not attach the feet if the equipment is to
be mounted on the wall.
•
When selecting the location for the equip-
ment, please note that if there are skirtings
on the floor, then the minimum distance to the
housing or the installation height has to be
measured from the top of the skirting.
•
To fasten the two upper wall holders (12) and
the lower wall holder (13) to the rear side of
the housing, insert the wall holder lug into the
slot (a). Then screw the wall holders (12 +
13) to the rear side of the housing, with one
M4x10 screw (15). The lower, central wall hol-
der (13) is needed only as a spacer and will
not be connected to the wall later.
•
Then drill the two fastening holes with 8 mm
diameter. Mark the centers of the holes so
that they are 535 mm apart, horizontal and at
least 650 mm above the floor (allow for skir-
tings), then drill the holes accordingly.
•
Insert the wall plugs (Fig. 2 / Item 14) and
turn the two screws (Fig. 2 / Item 17) into the
plugs far enough to enable the wall holders
to be hooked on. Hook the equipment by the
two upper wall brackets onto the screws. Pull
down the equipment as far as it will go, then
push it to the left until it hangs securely.

6. Operation

Warning! Before using the equipment for the fi rst
time, check that the voltage supply is the same as
the voltage details set out on the rating plate.
Read the safety regulations in section 1.
When the equipment is used for the fi rst time or
after a long period of rest, it may emit an odor for
a short time. This is not a fault.
When one of the function buttons is pressed, the
backlighting will come on for approx. 25 seconds.
All modes and functions can be set using the but-
tons on the appliance as well as with the remote
control. The remote control runs on 2 batteries
type „AAA". Make sure that the poles are not
reversed when you change the batteries. Used
batteries must be disposed of properly.
- 16 -
17.04.2018 09:07:34 17.04.2018 09:07:34