Conrad 97 25 88 Bedienungsanleitung Seite 3

O P E R A T I N G I N S T R U C T I O N S
WLAN multifunctional
USB print server
Item-No. 97 25 88
Intended use
The product is used for the connection of a USB printer or MFP (multifunction printer) to a
10/100MBit network.
An external power supply unit is used to supply the power.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Print server
• Network cable
• Wall plug transformer
• WLAN Antenna
• CD with software and the manufacturer's comprehensive English-language instructions
• Quick guide
Features
• A USB port for printer/MFP
• WLAN using 802.11b/g, 54 MBit
• RJ45 port (10/100MBit)
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases.
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE).
• The design of the wall plug transformer complies with protection class II. Only use
a standard mains socket as voltagesource for the power supply unit.
• Only use the external wallplug transformer supplied to power the unit.
• Only use the product in dry indoor areas.
The product must not get damp or wet as this may damage it, danger of a fatal
electric shock!
• The device is not a toy. Keep devices that operate on the mains voltage out of the
reach of children! Therefore, be especially careful when children are around. Use
the product out of the reach of children.
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• Handle the product with care, it can be damaged by impacts, blows, or acciden-
tal drops, even from a low height.
Start-up
Ideally, a DHCP server is activated in your network, i.e. all devices connected to the
network get their IP address automatically.
• Switch your printer off and connect it to the USB port of the print server.
• Connect the print server to your network via the RJ45 jack.
• Connect the round, low-voltage plug from the wall plug transformer to the appropriate jack on
the print server.
• Put the plug-in power supply into a mains socket. The power LED on the print server lights up.
• Now switch your printer on.
Software Installation
www.conrad.com
• Install the software first, which is provided with your printer. This must be done on all comput-
ers which shall have access to the printer or MFP later on. Install the software for the print serv-
er only after that.
Version 11/09
• Insert the CD provided in the appropriate drive on your computer. If the installation program
°
does not appear automatically, start the program "Setup.exe" in the „Utility" directory of the CD.
In case of newer CD versions, the procedure may be different.
Follow the software instructions.
After the installation select „Yes, I want to con-
figure the MFP Server now", click on „Next",
see right figure.
• Now the MPF server should be searched and
found, see right figure.
For this, it may be required to set up the fire-
wall/antivirus software so that the software of
the multifunction USB printer server has
access to your network. Otherwise, the pro-
duction may not work!
• Following that, a window appears with the request for a user name and a password. Enter
„admin" as user name and „1234" as password (without quotation marks).
• After that, a manual IP address for the print server can also be assigned between the auto-
matic IP address assignment per DHCP (depending on your network).
• Follow all further requests for the wireless network.
• Now Windows needs to be restarted.
• A new symbol „MFP Manager" is now on the Windows desktop which can be used to connect
the printer to the PC.
• Click on „Connect" to connect the printer that is connected to the print server to the corre-
sponding PC.
The hardware recognition of Windows may appear too, follow all the instructions.
• Other computers can only access the printer if you click on „Disconnect" on the computer that
is currently connected to the printer. Alternatively, you can set a time in the lower row, accord-
ing to which the connection is disabled automatically and the printer released for other users.
Resetting the print server to factory settings
• Press and hold the „Reset" key for 10 seconds and release it afterwards.
• Now the factory settings of the print server are activated again.
Pay attention to assign an IP address only once in your network when setting the
IP address manually.
The subnet mask, however (e.g. 255.255.255.0) should be the same for every com-
puter.