Inhaltszusammenfassung für ABB 83210-AP-xxx-500 Serie
Seite 1
VER:1.1 │ │ 06.07.2016 ABB-Welcome Pos : 2 /Di nA4 - Anleitung en Online/Inhalt/KN X/D oorEntr y/83220- AP- xxx/Titelbl att - 83220-AP- xxx - ABB @ 19\mod_1323249806476_15.doc x @ 111084 @ @ 1 83210-AP-xxx-500 Audio hands-free indoor station === Ende der Liste fü r T extmar ke Cover ===...
ABB devices Pos : 13 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/U mwel t (--> Fü r alle D okumente <--)/Hinweis e/Hi nweis - U mwelt - ABB El ektr ogeräte @ 19\mod_1323162745839_15.doc x @ 110867 @ @ 1 All packaging materials and devices from ABB bear the markings and test seals for proper disposal.
Seite 4
ABB-Welcome ABB products meet the legal requirements, in particular the laws governing electronic and electrical devices and the REACH ordinance. (EU-Directive 2002/96/EG WEEE and 2002/95/EG RoHS) (EU-REACH ordinance and law for the implementation of the ordinance (EG) No.1907/2006) — 4 —...
Seite 6
ABB-Welcome Functions Communication button 1A For incoming call, press this button to activate the communication within 30 seconds and press it again to end the call. 1B In standby mode, press this button to enter the communication menu. Unlock button 2A Press this button to open the door at any time.
ABB-Welcome 4.2.3 Set ringtone type Step 1: Hold "light" button for 3s to enter setting mode (4 LEDs are on) Step 2: Press button like below to change ringtone. Press "unlock" button to set ringtone type for doorbell. Press "light" button to set ringtone type for room to room intercom or call guard unit.
ABB-Welcome Pos : 79 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Übersc hriften (--> Fü r alle D okumente <--)/1. Ebene/M - O/Montage / Installation @ 18\mod_1302613966111_15.doc x @ 103373 @ 1 @ 1 Mounting / Installation Pos : 80 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Sic herheit (--> Fü r alle Dokumente <--)/Warnhinweis e/Sic herheit - Ni eders pannungs- und 230 V-Leitungen @ 18 \mod_1302617821491_15.doc x @ 103465 @ @ 1...
ABB-Welcome General installation instructions • Terminate all branches of the wiring system via a connected bus device (e.g., indoor station, outdoor station, system device). • Do not install the system controller directly next to the bell transformer and other power supplies (to avoid interference).
ABB-Welcome Pos : 84 /Busc h-J aeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Übersc hriften (--> Fü r alle D okumente <--)/2. Ebene/M - O/Montage @ 18\mod_1302615960458_15.doc x @ 103424 @ 2 @ 1 Mounting Pos : 85.1 /DinA4 - Anl eitungen Onli ne/Inhalt/KN X/DoorEntr y/83220-AP- xxx/M ontag e - M odul e/Montage - Montagedose -- 83220-AP- xxx @ 19\mod_1323250406848_15.doc x @ 111098 @ @ 1 Recommended installation height 1.5 meters (4.9 feet)
Seite 14
ABB-Welcome Installation dimensions for slotted screw holes 60 mm 60 mm 79 mm The bottom of the device has screw holes for fastening to the wall according to the dimension above. In addition, the bottom of the device can be affixed to the existing flush-mounted box.
Seite 15
ABB-Welcome Mounted on the wall Affix the bottom of the device to the wall. Latch the upper part of the device onto its bottom part .Place the upper side of the device on the lock-in lugs and then press the bottom side onto the bottom part of the device until it is caught by the clamp.
Seite 16
We reserve the right to, at any time, make technical changes or changes in the content of this document without prior notice. The detailed specifications agreed to at the time of ordering appl ies to all orders. ABB accepts no responsibility for possible errors or incompleteness in this document.