EINHELL HYPRESSO 18/24-1 Originalbetriebsanleitung Seite 20

5.2.3 Connecting the bottle adapter
(Fig. 3a-3b)
The bottle adapter (18) enables you to use a
water bottle as the source of water. The adapter
fi ts on most commercially available plastic water
bottles.
1. Twist the bottle adapter (18) onto the water
bottle (a) (Fig. 3a).
2. Insert the adapter into the water inlet (15) of
the cordless pressure washer (Fig. 3b). Make
sure that the connection is secure and does
not leak.
5.3 Charging the Li battery pack (Fig. 7-8)
1. Remove the battery pack (a) from the handle,
pressing the pushlock button (b) downwards
as you do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the socket outlet. The green LED will
then begin to blink.
3. Push the battery (a) onto the charger (c).
4. In the section entitled „Charger indicator" you
will fi nd a table with explanations of the LED
display on the charger.
Caution!
To prevent the battery from overheating, only ever
charge it without the PXC battery cover fi tted.
The battery can become a little warm during the
charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Anl_Hypresso_18_24-1_SPK13.indb 20 Anl_Hypresso_18_24-1_SPK13.indb 20
GB
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.4 Battery capacity indicator (Fig. 7/d)
Press the button for the battery capacity indicator
(e). The battery capacity indicator (d) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 Using for the fi rst time
Once you have completely assembled the tool
and made all the connections, you can proceed
as follows:
Open the water inlet. Press the safety device (1)
(Fig. 1) on the spray gun to release it, then press
the handle (3) (Fig. 1) to release any air from in-
side the equipment.
Now activate the trigger lever (2).
To switch off , release the trigger lever (2). The
equipment will then go into standby. As soon as
you press the trigger lever again, the pressure
cleaner will restart. You can choose between 2
pressure levels by pressing on Eco (4) (Fig.1).
- 20 -
14.02.2024 09:34:22 14.02.2024 09:34:22