Conrad 2522233 Bedienungsanleitung Seite 4

b) GPS system
Displayed information includes vehicle speed, battery performance, satellite numbers, progress bar.
Important
• Vehicles not compatible with OBD-II / EUOBD can only use GPS.
• The accuracy of GPS data will vary depending on factors affecting signal strength such as cloud
cover, inside tunnels, and being surrounded by tall buildings.
1. Connect the USB cable to the USB port on the HUD.
2. Connect the USB cable to a suitable power supply in your vehicle (e.g. auxiliary outlet with a suitable
adapter).
3. The GPS system turns on as soon as it receives power.
Operation
Button descriptions are when the wave button is facing towards the windscreen.
a) General
Setting Description
Switch between HUD and Within (5 s) of HUD flashing, slide the wave button left or right to switch
GPS modes between OBD and GPS modes.
1. Press and hold the wave button right (5 s) until all LED lights turn on.
Clear fault codes
2. Press and hold the wave button right (5 s) to return to the main screen.
System sound Push and hold left (2 s) to turn the system sound on/off.
b) HUD system
• Press down and hold the (2 s) to enter the settings menu.
• Push right or left to select a menu item (1 -11).
• Press down to enter the selected menu item.
• Press left/right to adjust values.
- Press down to exit settings and return to the settings menu.
- Press down and hold (2 s) to save settings and return to the main display.
Setting Function Range
Speed 50 - 150
RPM alarm 10 - 75
4-stage alarm 0 - 1
Over-speed alarm 0 - 199
Display mode 0 - 2
Display brightness 0 - 11
Speed unit 0 - 1
Temperature unit 0 - 1
Starting voltage 0 - 15.0
Shutdown time 5 - 199
Restore factory de-
0 - 1
fault settings
Troubleshooting
Problem Suggestion(s)
• Check the cable and connection.
No display / power to HUD.
• Try connecting the HUD and cable to another car.
HUD only shows battery voltage Make sure your vehicle supports OBD-II. If not, use the GPS system.
but shuts off after 30 s of driving. See section "Connection b) → GPS system".
Conflicts with other after market devices e.g. parking sensors, car
window closer, keyless entry etc.
HUD crashes Disconnect other devices then perform a factory reset.
See section "System settings → a) General → Restore factory de-
faults".
• Make sure the correct speed unit (km/h or mph) is set. See sec-
tion "Settings → b) HUD system → Setting 7".
Speed not accurate
• Offset the discrepancy. See section "Settings → b) HUD system
→ Setting 1".
HUD shuts down when the ve-
• Extend the shutdown time.
hicle is idle but not switched off,
• See section "Settings → b) HUD system → Setting 10".
e.g. hybrid vehicles.
Description
Offset any discrepancies between the vehicle speedom-
eter and HUD display. Default = 107
An alarm will sound when the engine rpm equals or ex-
ceeds the set value, e.g. 80 = 8500 rpm. Default = 75
0 = OFF ; 1 = ON ; Default = 0
Alert icon will light up at 60, 80, 100, 120 km/h
Set an alert icon to show at a certain speed.
Default = 150 km/h
0 = high speed (> 80 km/h, only speed shows)
1 = Shows all information ; 2 = Shows speed only
Default = 1
1- 11 (darkest - brightest) ; 0 = Automatic (default)
0 = km/h (default) ; 1 = mph
0 = ºC (default) ; 1 = ºF
If HUD does not automatically switch off when the igni-
tion is switched off, adjust the voltage.
E.g. 13.2 = 13.2 V. Default = 0.
If your car has a start-stop system e.g. gas-electric hy-
brid, you may need to extend the auto shutdown time.
Default = 20 s.
1. Set the parameter to 1.
2. Press and hold the wave button (5 s) to save and
restore default settings.
Problem Suggestion(s)
• Lower the starting voltage.
HUD cannot automatically switch
off
• See section "Settings → b) HUD system → Setting 9".
• Lower the starting voltage.
HUD randomly restarts
• See section "Settings → b) HUD system → Setting 9".
• Check the cable and connection.
No display image shown \ no
power to HUD.
• Try connecting the HUD and cable to another car.
• OBD connection: Lower the starting voltage.
HUD will not automatically start
or switches off while driving.
• See section "Settings → b) HUD system → Setting 9".
HUD does not turn off after
• OBD connection: Increase the starting voltage.
the vehicle ignition has been
• See section "Settings → b) HUD system → Setting 9".
switched off.
• Offset the discrepancy. See setion "Settings → b) HUD system
Speed not accurate
→ Setting 1".
Make sure the system sound is turned on.
Alarm set but no sound.
See section "Settings → a) General → System sound".
Care and cleaning
• Disconnect the product from the power supply before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product con-
forms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Select a language by clicking on a flag symbol and enter the product order number in the search
box. You can then download the EU declaration of conformity in PDF format.
Disposal
This symbol must appear on any electrical and electronic equipment placed on the EU market.
This symbol indicates that this device should not be disposed of as unsorted municipal waste
at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separate-
ly from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by
the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner,
must be removed by end users from the WEEE in a non-destructive manner before it is handed
over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste.
Conrad provides the following return options free of charge (more details on our website):
• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manu-
facturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in countries
outside of Germany.
Technical data
Input voltage / current ........................... OBD: 11 - 18 V/DC
GPS: 5 - 26 V/DC
Standby power consumption ................ ≤14 mA (via USB cable)
Light sensor .......................................... auto brightness adjust
Speed ................................................... km/h, mph
Compatibility ......................................... OBD-II, EUOBD
Barometric pressure ............................. 86 - 106 KPa
Frequency range .................................. 1.574 -1.577 GHz
Transmission power.............................. 0 dBm
OBD-II cable length .............................. approx. 1.7 m
USB cable length .................................. approx. 2.4 m
Operating/Storage conditions ............... -40 to +80 ºC, 10 – 95 % RH (non-condensing)
Dimensions ........................................... 91 x 53 x 25 mm (L x W x H)
Weight .................................................. 50 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2024 by Conrad Electronic SE. *2522233_v3_0124_02_dm_mh_en