Bosch 0601B19200 Originalbetriebsanleitung Seite 29

OBJ_BUCH-2303-002.book Page 29 Tuesday, March 3, 2015 4:32 PM
61 Stop screw for right-hand bevel angle range
62 Set screws of scale 18 for mitre angles
63 Screw for mitre angle indicator
64 Velcro strap
65 Laser lens cover
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Weight according to
EPTA-Procedure 01/2003
Protection class
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Max. cutting width
Mounting hole diameter
Permissible workpiece dimensions (maximum/minimum) see page 33.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 61029-1, EN 61029-2-9, EN ISO 12100, EN 60825-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 03.03.2015
Bosch Power Tools
Noise/Vibration Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 61029-2-9:
a =2.5 m/s
h
GCM 8 SDE
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
3 601 M19 2..
given in EN 61029 and may be used to compare one tool with
W 1600
another. It may be used for a preliminary assessment of expo-
-1
min 3500–5000
sure.

The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
nm 650
applications, with different accessories or poorly maintained,
mW < 0.39
the vibration emission may differ. This may significantly in-
1M
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
kg 18.9
take into account the times when the tool is switched off or
/II when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
mm 210–216
Identify additional safety measures to protect the operator
mm 1.3–1.8
from the effects of vibration such as: maintain the tool and the
mm 3.3 accessories, keep the hands warm, organisation of work pat-
terns.
mm 30
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Material clamp 29
– Hex key 36
– SDS bolt 51
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
(triax vector sum) and uncertainty K
h
2 2
, K=1.5 m/s .
1 609 92A 0Z4 | (3.3.15)
English | 29