DeWalt DWV905M Originalanweisung Seite 33

To Unpair with a Wireless Tool Control™ Tool
or Remote
1. Turn the on/off tool control switch to the
the trigger on the Wireless Tool Control™ equipped tool or
press the button on the remote at the same time.
2. The LED above the Wireless Tool Control™ pairing button will
flash slowly to indicate a successful unpairing.

CAUTION: To prevent unintentional switch-on after the end
of work Switch the On/Off switch
or unpair the Wireless Tool Control of tool or remote.
LED FLASH PATTERN
In pairing mode
No device is paired
Device is successfully paired
Fig. M
28
Replacing the Coin Cell Battery in the
Remote Control (Fig. H)
DANGER: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD.This product contains a coin /
button cell battery. If the coin / button cell battery
is swallowed, it can cause severe internal burns in
just 2 hours and can lead to death.
WARNING: KEEP NEW AND USED BATTERIES AWAY
FROM CHILDREN. If the battery compartment does not close
securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical attention.

WARNING: WHEN REPLACING BATTERY, REPLACE IT
WITH THE SAME OR EQUIVALENT TYPE CR2032. Observe
correct polarity (+ and –) when replacing batteries. Do not
store or carry batteries so that metal objects can contact
exposed battery terminals.

WARNING: ENSURE THAT COIN CELL REPLACEMENT IS
CARRIED OUT PROPERLY. There is a risk of explosion.
• When replacing battery, replace it with the same or equivalent
type CR2032. Do not use any other coin cells or other forms of
electrical power supply.
• Do not attempt to recharge the coin cell battery and do not
short circuit the coin cell battery. The coin cell battery may
leak, explode, catch fire and cause personal injury.
• Do not overheat the coin cell or throw it into fire. The coin cell
may leak, explode, catch fire and cause personal injury.
I position and pull
15 to the OFF (O) position.
– – – – – – –
– – – – – – – –
– – – –
27
• Do not damage the coin cell and do not disassemble the
coin cell. The coin cell may leak, explode, catch fire and cause
personal injury.
• Do not allow damaged coin cells to come into contact with
water. Leaking lithium may mix with water to create hydrogen,
which could cause a fire, an explosion, or personal injury.
• Do not dispose of the button cell battery with normal
household waste. Contact your local waste disposal
department to dispose of the device/batteries in accordance
with applicable local laws and regulations.
• Remove and dispose of drained coin cell correctly. Drained
coin cell may leak and damage the product or cause
personal injury.
1. To open the housing remove the 4 screws
panel with a T10 torx screwdriver.
2. Pull out sideways the discharged coin cell battery fom the
battery holder.
3. Insert sideways the new coin cell battery
battery holder, pay attention to the orientation of the
battery in terms of polarity.
4. Replace the back cover, insert the screws and tighten.
Fig. H
37
Automatic Filter Cleaning System
This vacuum has a highly effective filter cleaning system which
minimizes filter clogging. Every 30 seconds, one of the two filters
gets automatically cleaned. The cleaning process alternates
between the filters and continues through the life of the unit.
nOTE: After starting the vacuum, both filters get cleaned within
the first 15 seconds.
nOTE: It is normal to hear a clicking sound during this process.
nOTE: After many hours of operation the automatic filter
cleaning system may not be effective. When this happens, see
clause Filter under Maintenance.
Parking Brake (Fig. I)
The parking brake will lock one wheel in place to prevent
vacuum from rolling.
1. To engage parking brake, depress the brake
brake into the locked position.
2. To disengage parking brake, depress the brake button and
brake will snap into the unlocked position.
EnGLIsH
37 from the rear
into the
38
38
30 to snap the
31