Identification Of The Parts; Assembly - Texas TS4518 Bedienungsanleitung

Use safety trousers with leg protection, safety
shoes and gloves.
Keep all spectators, children, and pets at a
distance of at least 15 meters.
Keep long hair tied back.
The work area must be well lighted.
Stand firm and in balance. Do not reach too far out.
Never touch the area near the silencer and the
cylinder as these parts get hot when the engine is
running.
Always stop the engine and take off the lid of the
spark plug before making adjustments or repairs.
Make sure that the saw chain is fitted correctly and
securely fastened. If not this may lead to serious
personal injury.
Be extra careful when working with bushes and
small trees. Small branches can catch a hold of the
chain and be hurled against you or make you lose
your balance.
Due to vibrations from the handle, long time use
can result in white fingers.
If fatigue is felt in arms, hands or fingers – or visible
signs of white fingers is appearing, the work should
be stopped immediately, and a sufficient time of
break should be taken for recovery. To avoid white
fingers, each user should operate the machine for
no more than 1.5 hours per day
Follow the manual for filing and maintenance.
Gasoline safety
Use extreme care in handling gasoline. Gasoline is
extremely flammable and the fumes are explosive.
Serious personal injury can occur, when gasoline is
spilled on yourself or your clothes. Rinse your skin
and change clothes immediately!
Use only an approved gasoline container. Do not
use soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 1 cm below
bottom of filler in order to provide space for fuel to
expansion.
After refueling, ensure that the cap tighten
securely.
Never use the lock-function on the gasoline gun,
when refueling.
Do not smoke while refueling.
Never refuel inside a building or where gasoline
fumes may get in contact with an ignition source.
Keep gasoline and engine away from appliance,
pilot lights, barbecues, electric appliances, power
tools, etc.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are explosive.
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when doing
adjustments and when being transported by means
other than under its own power.
The engine must be completely cooled before
storing indoors or covered.
If the machine unused for a period of time, please
refer to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
All repair and maintenance procedures not
described in this user manual, must only be carried
out by specially trained staff at an authoried service
shop. Use of wrong tools can demage your chain
saw.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is
no longer applied.
Ensure that the machine is properly secured when
transported on a flatbed etc.

Identification of the parts

See Fig. 1 and illustration:
1. Rear handle/grip
2. Safety button
3. Throttle trigger
4. Top cover (for air filter and spark plug)
4a. Finger screw
5. Front handle/grip
6. Front handle guard (Chain brake)
7. Saw chain
8. Guide bar
9. Nose sprocket wheel
10. Retaining nut
11. Chain tension screw
12. Plastic guard
13. Rear hand safeguard
14. Threaded pins
15. Lubrication hole (chain oil)
16. Spiked bumper
17. Chain catcher
18. Clutch
19. Drive sprocket
20. Spark plug
21. Air filter
22. Choke knob + primer
23. Ignition start/stop switch
24. Fuel gauge
25. Fuel tank cap
26. Engine speed adjustment screws
27. Recoil starter handle
28. Chain oil adjustment screw
29. Air vents
30. Chain oil tank cap
31. Guide bar cover
32. Spark plug wrench
33. Screwdriver
34. Fuel mix container

Assembly

Installing guide bar and saw chain. Fig 1-7.
1. Attach the spiked bumper with the 2 included
screws (16).
2. Pull the chain brake handle (6) back towards the
machine, so that the brake is not activated.
Loosen the nuts (10) and remove the plastic cover
(12). Remove the plastic spacer before fitting guide bar
3. Place the guide bar (8) over the threaded pins
(14). Make sure to fit the guide bar with the "saw
chain" symbol at the top of the bar.
4. Push the guide bar (8) towards the drive sprocket
(19) behind the clutch (18).
5. Place the chain (7) around the drive sprocket (19)
with the teeth pointing forwards (towards the tip of
the guide bar). Place the chain's drive link, so that
it is in engaged correctly with the drive sprocket's
18