Consumables; Description Of The Device; Installation; Initial Start-Up - Kärcher WPD 200 Advanced Bedienungsanleitung

Description
Contact protection for water outlet
Conversion kit, glass pane, unprinted
Rinsing cup 4 l

Consumables

Device parts
Description
Active Pure filter
Removes bad tastes or odours (e.g. chlo-
rine), filters heavy metals, microplastics
and impurities from the supply system.
Hy Protect filter
Filters viruses, bacteria and microplas-
tics.
Aerator with sleeve
Aerator insert at the water outlet for
stream shaping
O-ring 11.91 x 2.62 KTW
Seal of the pressure reducer 4.640-588.0
on the bottle screw connection.
Detergent for exterior cleaning of device
Description
CA 30 R
Ready-to-use surface cleaner, 0.5 l bottle
Spray head for surface cleaner
When ordering CA 30 R for the first time,
this reusable spray head for the spray
bottle is required.
Disinfectant RM 735 (20 ml concen-
trate)
Empty bottle with spray head for pre-
paring RM 735

Description of the device

For the illustrations, refer to the graphics page
Illustration A
Display
1
Water outlet
2
Water connection
3
Power supply
4
Type plate
5
Fuse holder cover with 10 A fuse
6
Power switch
7
Ventilation openings
8
Hy Protect filter
9
Active Pure filter
10
Device door
11
Rinsing hose
12
Drip tray drain
13
Button
14
Unlocking button
15
Drip tray
16

Installation

Prerequisites
The following utilities are required to operate the device:
● Mains socket for connection to the mains.
● Water tap with 3/8" or 3/4" external thread for con-
nection to the water supply.
Attaching the attachment kits
1. Attach the attachment kits ordered for the device to
the device.
Note
The installation for each attachment kit is described in
separate installation instructions enclosed with the at-
tachment kit
Connecting the device
Order no.
DANGER
2.644-008.0
Danger from electric shock.
2.644-130.0
Do not remove the side parts, the lid or the circuit board
cover of the device. These components may only be re-
6.640-341.0
moved by an authorised electrician.
During initial installation and any repairs that involve the
replacement of accessory parts, make sure only parts
approved by KÄRCHER (filter, mains cable, connection
kit, CO2 pressure regulator (depending on equipment))
Order no.
are used. These components have been tested and cer-
2.643-773.0
tified to ensure compliance with KÄRCHER Quality
Standards. No other components may be used.
● The power connection and water input pressure
must correspond to the values in the technical data
2.643-306.0 (see chapter "Technical data").
● Depending on local regulations, an approved back-
flow preventer must be installed.
● For devices with drip tray drainage into the waste
4.640-519.0
water pipe on the building side, a siphon must be
provided to protect against odour nuisance from the
waste water pipe.
6.640-731.0
The siphon must be positioned lower than the drip
tray.
The drip tray drain only functions reliably when the
waste water hose is continuously hanging.
● Set up the device on a level surface.
● Mains plug and socket must always be freely acces-
Order no.
sible.
6.295-686.0
● The power switch, the fuse and water connection
(rear of the device) must be freely accessible. The
6.295-723.0
minimum distance to the wall is 100 mm.
● Do not use used hose lines.
Using the device with a stand:
● In order to ensure a high degree of stability of the
device in accordance with the guidelines of the de-
6.295-476.0
vice standard, a device with a stand must be se-
6.296-143.0
cured to the floor or wall (attachment kit for securing
6.296-148.0
to floor WPD 2.643-483.0).
● Alternatively, the attachment kit for additional weight
for stand WPD (2.643-474.0) can be used to lower
the device's centre of gravity accordingly.
Connection diagram:
Illustration B
Socket (fused with 30 mA error-current circuit
1
breaker)
Mains cable
2
Water dispenser WPD
3
Water supply hose (connection kit)
4
External backflow preventer (optional)
5
External pressure reducer with pressure gauge (on-
6
ly necessary with water inlet pressure above 6 bar
(0.6 MPa))
Aqua stop (optional)
7
Water tap of the building installation
8
Drinking water pipe of the building installation, ex-
9
ternal thread 3/8" or 3/4"
Waste water pipe
10
Siphon of the building installation
11
Drip tray drain
12
Connections:
Illustration C
Inlet screen
1
Water connection (connection thread 3/4")
2
Power supply
3
Rinsing hose (optional)
4
Drip tray drain (optional)
5
Connection as tabletop device
1. Attach the table-top attachment kit (2.644-180.0) ac-
cording to the enclosed installation instructions.
2. Run the rinsing hose to the siphon on the building
side.
3. Run a hose from the drip tray drain to the siphon.
4. If no waste water drain is available, use the attach-
ment kit can WPD (2.644-183.0).
a Connect the rinsing hose and the drip tray drain
to the screw cap of the can.
b Connect the fill level sensor cable to connector
X27 on the device.
English
Connection with stand
1. The stand attachment kit (white: 2.643-883.0, black:
2.643-884.0), if needed, also use the cup dispenser
attachment kit (2.644-181.0) and the additional cool-
er attachment kit (2.644-204.0). Attach the attach-
ment kits according to the enclosed installation
instructions.
2. Run the rinsing hose through the stand to the siphon
on the building side.
3. Attach an angle piece to the drip tray drain.
4. Run a hose through the stand from the elbow to the
siphon.
5. If no waste water drain is available, use the attach-
ment kit can WPD (2.644-183.0).
a Connect the rinsing hose and the drip tray drain
to the screw cap of the can.
b Connect the fill level sensor cable to connector
X27 on the device.
Connecting utilities
1. Connect the water inlet hose to the water connec-
tion on the back of the device using the enclosed
connection kit.
2. Connect the water supply hose to the tap of the
building installation (if necessary, connect additional
components).
3. Connect the mains cable to the power supply on
rear of device.
4. Connect the CO connection hose to the CO
2
nection.

Initial start-up

Opening the device door
1. Pull out the drip tray.
Illustration D
Drip tray
1
Device door
2
Unlocking button
3
2. Press the unlocking button and open the device
door.
Inserting the filter
1. Pull out the drip tray.
2. Open the device door.
WARNING
Health risk
Germs introduced into the device can contaminate the
water.
Pay special attention to hygiene and cleanliness when
replacing the filter cartridges.
Do not touch the connections and holders of the filters.
Wear sterile disposable gloves when changing filters.
Do not mix up the filters, observe the colour markings.
3. Do not touch the marked areas.
Illustration E
Areas that must not be touched.
1
4. Turn the cap to the left and pull it off downwards.
Illustration F
Cap
1
5. Turn the filter so that the handle is on the left side
and insert it from below into the corresponding hold-
er.
Illustration G
Support
1
Tab
2
Filter
3
Handle
4
6. Turn the filter to the right as far as it will go.
7. Check the installation position: The markings on the
label of the holder and on the filter must be aligned.
Illustration H
Marking
1
8. Close the device door.
9. Insert the drip tray.
con-
2
19