GRAPHITE 59G806 Betriebsanleitung Seite 13

CONSTRUCTION AND APPLICATION
The mitre saw is a device equipped with the base that provides
the possibility to change the angle of the cutting head attached
to it. In addition, depending on a design, the mitre saw head
can be tilted at an angle or slid out to increase the functionality
and cutting length.
The mitre saw is designed for cutting wooden pieces that
match with the tool size. Do not use the saw for cutting
firewood. Use the mitre saw accordingly to its purpose only.
Attempts to use the mitre saw for purposes other than
specified will be considered an improper use. Use the mitre
saw only with appropriate cutting discs with teeth with sintered
carbide inserts. The mitre saw is designed for carpentry works
in workshops and for joinery works.
The power tool should be used according to its purpose!
DESCRIPTION OF GRAPHIC PAGES
The below list refers to device components shown in the
graphic pages of this instruction manual.
* There can be differences between the drawing and real
product.
EQUIPMENT AND ACCESSORIES
1. Dust bag - 1 pcs
2. Socket wrench - 1 pcs
3. Vertical clamp - 1 pcs
PREPARATION FOR WORK
Make sure the mitre saw is disconnected from power supply,
before any adjusting or mo-unting works are commenced.
HANDLING THE MITRE SAW
• Make sure the head is locked in the lowest position when
carrying the mitre saw.
• Make sure that the work table locking knob, head locking
lever, and other safety parts are tightened firmly.
INSTALLING THE MITRE SAW ON A WORKSHOP BENCH
It is recommended to fix the mitre saw to a workbench or a
stand with the use of mounting holes (19) designed for such
purpose. They are located on the mitre saw base and
guarantee safe operation and eliminate risk of unwanted
machine shifts during operation. The holes allow to use bolts
with hexagonal head and 8 mm in diameter.
When fixing the mitre saw to a workbench ensure that:
• The workbench top surface is flat and clean.
• Screws and bolts are tightened equally and moderately
(mounting bolts must be tightened so the base is not stressed
or deformed). In case of over-stress there is danger of
breaking the base.
DUST EXTRACTION
To prevent dust accumulation and provide maximum
efficiency, you can connect the mitre saw to an industrial
vacuum cleaner using the dust extraction connector (28)
Alternatively, you can collect the dust in the dust-bag
(included) after installing it onto the dust extraction connector.
To install, put the dust bag (29) onto the dust extraction
connector (28) (fig. A). To empty the dust bag, remove it from
the dust extraction outlet and open the zip-fastener that allows
to access inside the bag.
To achieve optimal dust extraction empty the bag when it
is 2/3 full.
USING THE EXTENSION ARM (HEAD)
There are two positions of the extension arm – upper and
lower. To release the extension arm from locked lower
position, do as follows:
• Press and hold down the extension arm.
• Pull the head locking pin (9).
• Hold the extension arm as it raises to its upper position.
To lock the extension arm in the lower position, do as follows:
• Press and hold the disc guard lever (5).
• Release the pressure downwards onto the extension arm
until it is located in its lower position.
• Lock the extension arm in this position, sliding the head
locking pin in (9).
VERTICAL CLAMP
The vertical clamp (fig. B) can be installed in the saw base at
either side of the work table and is fully adjustable to size of
the workpiece to be cut. Do not use the saw without using the
vertical clamp.
• Loosen the vertical clamp mounting knob (30) to the base on
the side, which the vertical clamp will be installed.
• Install the vertical clamp by sliding it into the hole in the mitre
saw base and tighten the vertical clamp mounting knob (30) to
the mitre saw base.
• Once the vertical clamp arm position is adjusted (31) to the
workpiece, tighten the vertical clamp arm locking knob (32)
and workpiece mounting knob (33).
• Make sure the workpiece is secured.
OPERATION / ADJUSTMENTS
Make sure the mitre saw is disconnected from power
supply, before any adjusting or mounting works are
commenced. To ensure safe, precise and efficient
operation of the mitre saw, proceed with all adjustment
procedures as a whole.
After finishing all the setting and adjustment procedures,
ensure that all spanners are collected. Check that all
threaded connections are properly tightened.
When making adjustments, ensure that all external parts
work properly and are in good condition. Any worn or
damaged part must be replaced by qualified personnel
before starting to use the mitre saw.
SWITCHING ON /SWITCHING OFF
The mains voltage must correspond to the value specified
on the mitre saw nameplate.
Switch on the mitre saw only when the cutting disc is away
from the workpiece to be cut.
The mitre saw features the switch lock button (3) that protects
against accidental starting.
Switching ON
• Press the switch lock button (3).
• Press and hold the switch button (4).
12