Helpful Hints - DeWalt XR DCD791 Bersetzt Von Den Originalanweisungen

English
tool, the user will have to release the trigger and repress lock-
on button.
Speed Selector (Fig. A)
DCS356
Your tool is equipped with a speed selector
you to select one of the three speeds that limits the full speed.
Select the speed based on the application and control the speed
of the tool using the variable speed trigger switch
LED Worklight (Fig. P)
The LED worklight 2 will activate when the trigger is depressed.
It will automatically shut off following a short period of time
once the trigger is released.
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. R)
1. Attach the dust extraction adaptor
the Dust Extraction Adaptor.
2. Attach the sanding platen
Installing/Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust Extraction Adaptor.
2. Push dust extraction arm 19
dust extraction adaptor 17
3. Attach plunge cutting blade as described under Installing/
Removing Accessories.
4. Adjust the dust extraction arm

Helpful Hints

• Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
• Do not start sanding without having the sandpaper
attached to sanding platen.
• Use coarse grit paper to sand rough surfaces, medium grit
for smooth surfaces and fine grit for the finishing surfaces. If
necessary, first make a test run on scrap material.
• Excessive force will reduce the working efficiency and cause
motor overload. Replacing the accessory regularly will
maintain optimum working efficiency.
• Do not allow the sandpaper to wear away, it will damage
the sanding pad.
• If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for 2–3
minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
14
which allows
10
1 .
17 . Refer to Attaching
23 as described under
into the lower aperture of the
.
19 for best results.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Compatible accessories
Oscillating sanding pad
Oscillating wood w/ nails blade
Wide titanium oscillating wood w/ nails blade
Oscillating hardwood blade
Oscillating fastcut wood blade
Wide oscillating fastcut wood blade
Oscillating wood detail blade
Oscillating titanium metal blade
Oscillating semicircle blade
Oscillating titanium semicircle blade
Oscillating flush cut blade
Titanium oscillating flush cut blade
Oscillating multi-material blade
WALT recommended
e