Fujitsu DL7600Pro Bedienungshandbuch Seite 118

DER VOREINSTELLUNGSBETRIEB
5-12
*** Setup Parameters ***
<< Menu 1 settings >>
-------------------------
Func. Item Option
-------------------------
MENU1 EMULATE DPL24C+
MENU1 FONT COUR 10
MENU1 QUALITY LETTER
MENU1 PITCH 10 CPI
MENU1 LINE SP 6 LPI
MENU1 CHAR-W NORMAL
MENU1 CHAR-H NORMAL
MENU1 ATTRIB NONE
MENU1 PAGE LG 11.0 IN
MENU1 LFT-END 1 COLM
MENU1 TOP-MRG 1 LINE
MENU1 LANGUGE PAGE437
MENU1 CHR-SET SET2
MENU1 PRF-SKP NO-SKIP
MENU1 WIDTH 13.6 IN
MENU1 ZEROFNT NO-SLSH
MENU1 DC3-CDE ENABLE
MENU1 CR-CODE CR ONLY
MENU1 LF-CODE LF & CR
MENU1 RGHTEND WRAP
MENU1 INT-MEC DISABLE
MENU1 ==END==
-------------------------
<< Hardware settings >>
-------------------------
Func. Item Option
-------------------------
HARDWRE PPR-OUT DETECT
HARDWRE PRT-DIR BI-DIR
HARDWRE BUZZER ON
HARDWRE WORD-LG 8 BIT
HARDWRE BUFFER 8KBYTE
HARDWRE SENLEVL 100%
HARDWRE STANDBY 1MIN
HARDWRE INTRFCE AUTO-2S
HARDWRE FORMAT 8NONE 1
HARDWRE BAUD-RT 9600
HARDWRE PROTOCL XON/XOF
HARDWRE DSR IGNORE
HARDWRE DUPLEX FULL
HARDWRE CTS DETECT
HARDWRE CD IGNORE
HARDWRE ==END==
-------------------------
<< Adjust settings >>
-------------------------
Func. Item Option
-------------------------
ADJUST FCNTORG 1.8/6IN
ADJUST FCNTFIN 0 /180
ADJUST RCNTORG 1.8/6IN
ADJUST RCNTFIN 0 /180
ADJUST FCUTORG 1.8/6IN
ADJUST FCUTFIN 0 /180
ADJUST RCUROTG 1.8/6IN
ADJUST RCUTFIN 0 /180
ADJUST FCNTBTM 0 /180
ADJUST RCNTBTM 0 /180
ADJUST CUT-BTM 0 /180
ADJUST CNT-LFT 0 /90
ADJUST CUT-LFT 0 /90
ADJUST FCNTADJ 0 /360
ADJUST RCNTADJ 0 /360
ADJUST FCNTAJL 0 /360
ADJUST RCNTAJL 0 /360
ADJUST CUT-ADJ 0 /360
ADJUST FCSFADJ 0 /360
ADJUST RCSFADJ 0 /360
ADJUST FCNTLOR 4 /9
ADJUST FCNTLFN 0 /90
ADJUST RCNTLOR 4 /9
ADJUST RCNTLFN 0 /90
ADJUST CUTLOR 1.8/9
ADJUST CUTLFN 0 /90
ADJUST FCNTCUT 99 /180
ADJUST RCNTCUT 99 /180
ADJUST CUT-CUT 20 /180
ADJUST FRCSLNT 28/360
ADJUST ==END==
-------------------------
*1 FORMAT bis CD werden nicht gedruckt, wenn für INTRFCE die Option PARALEL
OPTION gewählt ist.
*2 TEAR-EN wird gedruckt, wenn für TEAROFF die Option AUTO gewählt ist.
Ausdruck der werkseitigen Einstellungen über LIST
<< Menu 2 settings >>
-------------------------
Func. Item
-------------------------
MENU2 EMULATE DPL24C+
MENU2 FONT
MENU2 QUALITY LETTER
MENU2 PITCH
MENU2 LINE SP 6 LPI
MENU2 CHAR-W
MENU2 CHAR-H
MENU2 ATTRIB
MENU2 PAGE LG 11.0 IN
MENU2 LFT-END 1
MENU2 TOP-MRG 1
MENU2 LANGUGE PAGE437
MENU2 CHR-SET SET2
MENU2 PRF-SKP NO-SKIP
MENU2 WIDTH
MENU2 ZEROFNT NO-SLSH
MENU2 DC3-CDE ENABLE
MENU2 CR-CODE CR ONLY
MENU2 LF-CODE LF & CR
MENU2 RGHTEND WRAP
MENU2 INT-MEC DISABLE
MENU2 ==END==
-------------------------
<< Config settings >>
-------------------------
Func. Item
-------------------------
CONFIG TEAROFF MANUAL
CONFIG TEARPOS VISIBLE
CONFIG TEAR-EN 1 SEC
CONFIG CUTLOAD AUTO
CONFIG LOADTIM 1.5 SEC
CONFIG DECODE
CONFIG FCNTARE ENABLE1
(*1) CONFIG RCNTARE ENABLE1
(*2) CONFIG CUT-ARE ENABLE1
(*2) CONFIG CUT-ONL ONLINE
(*2) CONFIG CNT-ONL ONLINE
(*2) CONFIG LOCK
(*2) CONFIG //S//
(*2) CONFIG FCNT-PE EDGE
(*2) CONFIG RCNT-PE EDGE
CONFIG GATHER
CONFIG CUT-CTL SPEED
CONFIG SKIP-PR ENABLE
CONFIG STATUS
CONFIG BANDCTL DISABLE
CONFIG TOF-CTL DRIVER
CONFIG FCNT-SF DISABLE
CONFIG RCNT-SF DISABLE
CONFIG CUT-SF
CONFIG CUTEDIR FRONT
CONFIG CSFEDIR REAR
CONFIG CUTEJCT AUTO
CONFIG FL-CENT POSN1
CONFIG RL-CENT POSN1
CONFIG SKEWCNT PRCISIN
CONFIG FF-CODE EJECT
CONFIG CSFBIN1 FRONT
CONFIG CNT-LD
CONFIG CSF-LD
CONFIG CSFAPTC NORMAL
CONFIG LF-CTL
CONFIG PR-MODE NORMAL
CONFIG HI-IMPT DISABLE
CONFIG LQ-MODE MODE1
CONFIG DQ-MODE MODE2
CONFIG POW-POS NORMAL
CONFIG ==END==
---------------------------
<< Gap Adjust settings >>
---------------------------
Func. Item
---------------------------
GAP-ADJ AMOUNT
GAP-ADJ ==END==
---------------------------
Bedienungshandbuch
Option
COUR 10
10 CPI
NORMAL
NORMAL
NONE
COLM
LINE
13.6 IN
Option
(*3)
(*4)
DIRECT
NONE
DISABLE
DISABLE
DISABLE
DISABLE
SPEED
NORMAL
SPEED
Option
AUTO