What Is Included In The Box; Remote Control; Initial Setup - Sharp CP-SS30 Bedienungsanleitung

What is included in the box:

• CP-SS30 bookshelf speakers
• Remote control (incl. batteries)
• Speaker connection cable (3m)
• RCA audio cable
• AUX audio cable
• Power cable
• User documentation
Controls
(Refer to 1 on page 1).
1. Removeable speaker grilles
2. LED indicator
• Standby - Red
• Bluetooth - Blue
• Aux in - Green
• RCA - Cyan
• Optical Mode - Yellow
• USB - Purple
3. / Volume/ source/ power control
• Long press to turn on or enter standby mode.
• Short press to change the mode (Bluetooth, Aux-in, RCA, Optical,
USB).
• Rotate to adjust the volume level.
Inputs/outputs
(Refer to 2 on page 1).
1. USB input
2. Optical input
3. RCA phono inputs
4. Aux in
5. ~AC power input
6. Audio output for connecting passive left speaker

Remote control

(Refer to 3 on page 2).
1. Press to power on or enter standby.
2. LOUD Loudness compensation increases the low and high frequen-
cies when listening at low volume.
3. Press to mute the sound. Press again to resume sound, or press
+/- to resume sound.
4. In Bluetooth and USB mode, short press for previous track, long
press to rewind.
5. In Bluetooth and USB mode, short press to play/pause.
6. In Bluetooth and USB mode, short press for next track, long press
to fast forward.
7. Short press to enter Bluetooth mode.
Long press to disconnect from paired device.
8. AUX Short press to change audio source to Aux.
9. RCA Short press to change audio source to RCA.
10. OPT Short press to change audio source to Optical.
11. USB Short press to enter USB mode.
12. EQ Short press to confi rm current EQ mode.
Continue pressing to cycle through the EQ presets.
13. +/– Press to adjust the volume.
14. BASS +/– Press to adjust the custom EQ bass level.
15. TRE +/– Press to adjust the custom EQ treble level.
Remote control operation
FIRST-TIME USE: The unit has a pre-installed lithium CR2025 battery.
Remove the clear isolating tab to activate the remote control battery.
The supplied remote control allows the unit to be operated from a
distance.
• Even if the remote control is operated within the eff ective range of
6m, remote control operation may be impossible if there are obstacles
between the unit and the remote control.
• If the remote control is operated near other products which generate
infrared rays, or if other remote control devices using infra-red rays are
used near the unit, it may operate incorrectly. Conversely, the other
products may operate incorrectly.
Remote control battery replacement
2
1
The remote control requires a CR2025, 3V Lithium battery.
1. Push the tab on the side of the battery tray towards the centre.
2. Slide the battery tray out of the remote control.
3. Remove the old battery. Place a new CR2025 battery into the tray with
the correct polarity (+/-) as indicated.
4. Slide the tray back into the slot in the remote control until it clicks in
to place.
Initial set-up
Placement of speakers
To enjoy stereo sound, place the "active" speaker unit (the unit with
controls on the front and inputs on the back) on the right hand side. The
other "passive" speaker should be on the left. We recommend the speakers
should be positioned at least 50cm apart. Ensure the speakers are not
obstructed.
Speaker connection
Before powering the unit, connect the left and right speakers using the
speaker connection cable provided. Please observe the polarity when
connecting the speakers: Connect the red cable to the red output, and the
clear cable to the black output on both speakers.
Connect to power
Risk of product damage! Ensure that the power supply voltage
corresponds to the voltage printed on the back or the underside of the
unit.
Connect the power cable to the ~AC power input of the unit and then
insert the plug in to a power socket.
EN
3
4