Ec Declaration Of Conformity - Milwaukee M18 FCSRH66 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für M18 FCSRH66:

Seite von 139

/ 139
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

ELECTRIC BRAKE

The electric brake engages when the trigger is released, causing

the blade to stop and allowing you to proceed with your work.

Generally, the saw blade stops within two seconds. However, there

may be a delay between the time you release the trigger and when

the brake engages. Occasionally the brake may miss completely.

If the brake misses frequently, the saw needs servicing by an autho-

rized Milwaukee service facility. You must always wait for the blade

to stop completely before removing the saw from the workpiece.

BATTERIES

Battery packs which have not been used for some time should be

recharged before use.

Temperatures in excess of 50°C (122°F) reduce the performance of

the battery pack. Avoid extended exposure to heat or sunshine (risk

of overheating).

The contacts of chargers and battery packs must be kept clean.

For an optimum life-time, the battery packs have to be fully char-

ged, after use.Battery packs which have not been used for some

time should be recharged before use.

To obtain the longest possible battery life remove the battery pack

from the charger once it is fully charged.

For battery pack storage longer than 30 days: Store the battery

pack where the temperature is below 27°C and away from moisture

Store the battery packs in a 30% - 50% charged condition Every six

months of storage, charge the pack as normal.

Do not dispose of used battery packs in the household refuse or

by burning them. Milwaukee Distributors oﬀer to retrieve old

batteries to protect our environment.

Do not store the battery pack together with metal objects (short

circuit risk).

Use only System M18 chargers for charging System M18 battery

packs. Do not use battery packs from other systems.

Never break open battery packs and chargers and store only in dry

rooms. Keep dry at all times.

Battery acid may leak from damaged batteries under extreme load

or extreme temperatures. In case of contact with battery acid wash

it oﬀ immediately with soap and water. In case of eye contact rinse

thoroughly for at least 10 minutes and immediately seek medical

attention.

No metal parts must be allowed to enter the battery section of the

charger (short circuit risk).

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit

situations that cause high current draw, the tool will stop for about

2 seconds and then the tool will turn OFF. To reset, release the

trigger. Under extreme circumstances, the internal temperatur of

the battery could become to high. If this happens, the battery will

shut down. Place the battery on the charger to charge and reset it.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legisla-

tion requirements.

Transportation of those batteries has to be done in accordance with

local, national and international provisions and regulations.

The user can transport the batteries by road without further

requirements.

English

Deutsch

Commercial transport of Lithium-Ion batteries by third parties is

subject to Dangerous Goods regulations. Transport preparation and

transport are exclusively to be carried out by appropriately trained

persons and the process has to be accompanied by corresponding

experts.

When transporting batteries:

Ensure that battery contact terminals are protected and insulated

to prevent short circuit. Ensure that battery pack is secured against

movement within packaging. Do not transport batteries that are

cracked or leak. Check with forwarding company for further advice

MAINTENANCE

Be sure to disconnect the tool from the power supply before

attaching or removing the saw blade.

Clean tool and guarding system with dry cloth.

Certain cleaning agents and solvents are harmful to plastics and

other insulated parts.

Keep the apparatus handle clean, dry and free of spilt oil or grease.

Check the function of guards.

Regular maintenance and cleaning provide for a long service life

and safe handling.

The ventilation slots of the machine must be kept clear at all times.

Remove dust regularly. Remove the sawdust which has accummu-

lated inside the saw in order to avoid the risk of ﬁre.

Use only Milwaukee accessories and Milwaukee spare parts. Should

components need to be replaced which have not been described,

please contact one of our Milwaukee service agents (see our list of

guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. Please

state the Article No. as well as the machine type printed on the

label and order the drawing at your local service agents or directly

at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Win-

nenden, Germany.