Assembly; Mh540; Installing The Cultivator Blades (02); Installing The Depth Skid (03) - AL-KO MH540 Betriebsanleitung

Assembly

4 ASSEMBLY
WARNING! Danger if assembly is not
carried out completely! Use of an incompletely
assembled device can result in serious injury.
■
Only use the device when it is fully assem-
bled!
■
Before switching on, check that all safety and
protective devices are in place and function-
ing correctly!
4.1

MH540

4.1.1

Installing the cultivator blades (02)

1. Fit the supplied cultivator blade sets (02/1)
onto the preassembled cultivator blade sets
(02/2).
2. Position the cultivator blade set so that the
holes are aligned with one another.
3. Insert the clip pin (02/3) through the hole and
secure.
4.1.2

Installing the depth skid (03)

1. Move the fastening sleeve of the depth skid
(03/1) into the base carrier (03/2) (03/a).
2. Insert the hexagon bolt (03/3) through the
hole and screw on the nut.
4.1.3

Installing the transport wheel (04)

1. Move the wheel mount with transport wheel
(04/1) through the hole into the front base
carrier (04/2).
2. Push on the spring (04/3).
3. Fit the washer (04/4) and nut (04/5) and tight-
en.
4.1.4 Installing the handlebar with handle
(05 - 06)
1. Position both lower braces (05/1) on the base
carrier (05/2) so that the holes are aligned.
2. Fully insert the bolts (05/3).
3. Fit nuts and tighten.
4. Position the upper brace (06/1) on the lower
brace (06/a) so that the holes are aligned.
5. Fully insert the bolts (06/2).
6. Fit washers and nuts, and tighten.
4.1.5

Installing the clutch lever (07)

1. Insert the clutch lever (07/1) with threaded
pins through the holes on the handlebar
(07/2).
2. Fit nuts (07/3) and tighten.
443277_b
4.1.6

Installing the guard plate (08)

The guard plates are installed to the right and left
of the engine in the same way.
1. Position (08/a) the guard plate (08/1) on the
holding plate (08/2) so that the holes are
aligned with one another.
2. Insert the bolts (08/3) from above into the
holes.
3. Fit nuts and tighten.
4.2

MH770

4.2.1

Preassembling the cultivator blades (10)

Four cultivator blades are mounted onto each
shaft fastening plate.
1. Place two cultivator blades (10/1) on each
side of the fastening plate (10/2). In the pro-
cess, position each cultivator blade offset by
90° to the next blade.
2. Insert four bolts (10/3) through the holes in
the cultivator blade and fastening plate.
3. Screw on the nut (10/4).
4.2.2

Installing the cultivator blades (11)

1. On both sides, fit a cultivator blade set (11/1)
onto the axle mount.
2. Fit additional cultivator blade sets.
3. Connect all cultivator blade sets together with
clip pins.
4. Fit a protective disc (11/2) on both sides and
secure using a clip pin on each.
4.2.3

Installing the depth skid (12)

1. Insert the fastening sleeve of the depth skid
(12/1) into the base carrier (12/2) (12/a).
2. Slide the locking pin (12/3) through the hole
and secure with spring split pin.
4.2.4

Installing the transport wheel (13)

1. Slide the wheel mount with transport wheel
(13/1) onto the front base carrier (13/a), so
that the holes are aligned.
2. Insert wheel mount through the hole (13/2).
3. Slide the spring (13/3) onto the wheel mount.
4. Fit the washer (13/4) and nut (13/5) and tight-
en.
4.2.5 Installing the handlebar with handle
(14)
1. Position (14/a) the handlebar (14/1) on the
base carrier (14/2).
2. Insert the bolt (14/3) through the grid joint.
3. Fit the clamping lever (14/4) and tighten.
29