cam REGOLO Bedienungsanleitung Seite 30

REGOLO 23 novembre 2016_Layout 1 25/11/16 09:10 Pagina 30
INSTRUCTIONS FOR USE
30. First open the buckle as shown in the
figure.
31. move the straps to the side (Fig. 31a)
and place your child on the seat (Fig. 31b).
32. Fasten the buckle as shown in the
figure until a click is heard.
33. check that the five harness straps are
placed correctly on your child and then
pull the central cord of the regulator hard
(Fig. 33a). Note: the child's harness must
be taut and fit closely to the body; if your
child is wearing bulky clothes, it is
advisable to remove them so that the
harness is tauter for greater SaFety.
REMOVING THE 5-POINT HARNESS
(art.162 e 163):
34. to transform the child safety seat for
use in groups ii and iii, the 5-point harness
must be removed first as shown in the
figure.
35. then the two optional inserts must be
removed. note: the inserts can also be
removed for use in group 1, following the
instructions in Fig. 34, if your child is of a
size not to need them. the inserts can be
fitted again by repeating the operation in
reverse.
36. FITTING AND USE group II and III
(art.162 and 163), follow the sequence in
Fig. 36, place the headrest at the required
height so that the diagonal belt D is just
slightly higher than your child's shoulder,
as shown in Fig. 36a. then tighten the
belts well so that they fit perfectly to your
child's body. if the child safety seat is fitted
using only the car safety belts (Fig.36b), it
belongs to the universal category, if it is
fitted using the car seat belts and
connectors, it is classified as semi-
universal. NOTE: do not fit the top-tether
(Fig. 36-c).
REMOVING AND WASHING THE COVER
OF THE CHILD SAFETY SEAT (art.162 e
163)
37. Follow the sequence shown in figures
37-38-39-40-41-42. Note: the cover can
29
be hand washed in warm water (max. 30°)
using neutral washing powder. Do not
spin dry! Do not iron! Do not use solvents!
43. CAUTION: when re-fitting the 5-
point harness be careful not to twist it
(Fig. 43B).
44. SPARE PARTS:
FABRIC PARTS
1a-heaDReSt
1b-cheSt paDS l.h.+r.h.
1c-Seat coveR
1d-belt paD
1e-inSeRt cUShion
1f-heaD hUggeR
1g-SiDe WingS l.h.+r.h
EPS-PU PARTS
2a-leFt-hanD epS SiDe impact pRotection
(3pcs)
2b-Right-hanD epS SiDe impact pRotection
(3pcs)
2c-epS heaDReSt pRotection
2d-epS Seat kit (4pcs)
2e-pU Seat paDDing
STRUCTURAL PARTS
3a-complete 5-point haRneSS
3b-top tetheR
3c- UppeR belt SaFety gUiDe l.h.+r.h.
3d-loWeR belt SaFety gUiDe l.h.+r.h.
3e- coveRS FoR belt gUiDe (4pcs)
3f- metal Seat-locking RoD
3g-metal RoD SUppoRt
3h-SiDe coveR l.h.+r.h.
3i- 5-point haRneSS locking RoD
3m-belt SliDing SyStem l.h. + r.h.
3n- belt gUiDe Seat pRotection
3p-SpRing kit 2pcs
3r- complete boDy
OTHER
4a- iSoFiX connectoR gUiDeS 2pcs
4b- inStRUction manUal
4c- aDheSive StickeR kit