ESX VISION ANDROID Serie Installationsanleitung
Vorschau ausblenden
Andere Handbücher für VISION ANDROID Serie:
- Benutzerhandbuch (40 Seiten) ,
- Einbauanleitung (21 Seiten) ,
- Installationsanleitung (16 Seiten)
Verwandte Anleitungen für ESX VISION ANDROID Serie
Inhaltszusammenfassung für ESX VISION ANDROID Serie
- Seite 1 VN950-4G / VN1 050-4G VNA-EXT-KIT1 00 (OPTIONAL) SMART NAVICEIVER MOBILE INTERNET READY V I S I O N A N D R O I D S E R I E S ™...
- Seite 2 IMPORTANT NOTES This guide is an aid for the professional installation of the device. Please note the following notes before installation: • Always handle all parts of the device and the components of your vehicle with care. • Under all circumstances observe the regulations of the vehicle manufacturer and do not make any changes to the vehicle which could impair driving safety.
-
Seite 3: Reset Button
MICRO SD SLOT FOR NAVIGATION SOFTWARE You can insert the MicroSD card of the navigation software here. Please only use the upper MicroSD card slot. The lower MicroSD card slot is only suitable for media. RESET BUTTON If the device stops responding to input, the system is overloaded or crashed. Then reboot the system by pressing the reset button (RST) on the front panel. -
Seite 4: Scope Of Delivery
SCOPE OF DELIVERY ITEM FIGURE QUANTITY Main device Monitor ISO system cable set AV cable set 1 with all audio and video connections as well as connection for external microphone (20-pin connector) AV cable set 2 with video outputs 1 and 2, power supply for camera (10-pin connector) Camera / microphone cable set... - Seite 5 SCOPE OF DELIVERY ITEM FIGURE QUANTITY USB ports (8-pin connector) 4G/LTE dongle (6-pin connector) GPS antenna WIFI antenna DAB antenna 4G/LTE antennas Fastening screws 1.5 mm hexagon socket...
-
Seite 6: Wiring Diagram
WIRING DIAGRAM WIRING DIAGRAM WiFi antenna WiFi antenna Monitor only in connection with the separately available installation set VNA-EXT-KIT100 4G/LTE antennas 4G/LTE antennas Inputs for AV cable sets Inputs for AV cable sets 20-pin system socket 20-pin system socket (G and D can be assigned (G and D can be assigned with fuse with fuse... -
Seite 7: Installation Hints
Lay the supplied cable sets and antennas in the vehicle. Please note the information on the next page. Then connect all cable sets, antennas and dongles to the ESX main device as described on page 7. Then plug in the cable plug from the radio slot of the vehicle on the ESX main unit or on its vehicle-specific system cable set. -
Seite 8: General Installation Instructions
Kleben Sie das Erdungsblatt der Verstärkereinheit auf den Metallteil auf der Frontsäule. GENERAL INSTALLATION INSTRUCTIONS Reinigen Sie die Windschutzscheibe mit auübersicht einem geigneten Reinigungstuch. enne sollte aus Sicherheitsgründen auf der Beifahrerseite GPS antenna rt werden. The GPS antenna must be glued horizontally to the front of the dash- Remove the film on board. -
Seite 9: Assembling The Device
ASSEMBLING THE DEVICE NOTE: Before assembling the device, you must insert the microSD card of the navigation software into the device (see page 3 above). If necessary, you can insert an additional MicroSD card for media into the lower card slot. MAIN DEVICE MONITOR First, connect the plug of the main unit to the monitor. - Seite 10 VNA-EXT-KIT100 INSTALLATION (OPTIONAL) With the separately available installation set VNA-EXT-KIT100, it is possible to install the monitor separately from the main device in the vehicle. The set is required e.g. for many Volkswagen vehicles in which the head unit is positioned in the glove compartment. INSTALLING THE DEVICE WITH VNA-EXT-KIT100 First remove the short connection cable Then attach the cover to the main de-...
- Seite 11 Quad- lock connection. Then lay the 1 meter long connection Then slide the ESX main device into the cable of the monitor through the dash- installation slot in the glove compart- board to the installation location of the ment until the retaining clips snap into monitor and connect it there.
- Seite 12 SETUP THE 4G/LTE INTERNET CONNECTION First lay the two 4G/LTE antennas inside the dashboard towards the windshield, one antenna for the left and one for the right. Ideally, you should stick the antennas to the windshield to ensure optimal recep- tion.
- Seite 13 SETUP THE 4G/LTE INTERNET CONNECTION Then turn on the device to test the 4G/LTE connection. After the device has started, enter After successful entry, the SIM card is your 4-digit PIN code of the SIM card unlocked. here. Confirm the entry with the tick. If the device is successfully connect- If the device is turned off, you have ed to the mobile Internet, the „4G“...
- Seite 14 TECHNICAL DATA / RADIO SYSTEM TYPE Function Band Information Frequency Range Max. emitted power GLONASS 1.575 MHz / 1.602 MHz – AM Radio Medium wave 520 - 1.700 Hz – FM Radio Band II 87,5 - 108 MHz – DAB Radio Band III (5A –...
- Seite 15 NOTES...
- Seite 16 ESX Car Media Systems · Audio Design GmbH Am Breilingsweg 3 · D-76709 Kronau/Germany Tel. +49 7253 - 9465-0 · Fax +49 7253 - 946510 www.esxnavi.de - www.audiodesign.de © All rights reserved. Subject to technical changes and errors.