Inhaltsverzeichnis
Werbung
To assemble the handlebar
1. On CT 36-5A EU FOLD-ADJ-T: Lift the handle until it
is straight and tighten the knob (A). (Fig. 24)
2. Attach the wires to the handlebar with cable ties.
To install the handle
1. Pull the blade pitch cable (A) from the bottom end of
the handle and remove the cable nut (B). (Fig. 25)
2. Remove the 2 bolts (C) and the 2 nuts (D) from the
handle holder. (Fig. 26)
3. Lubricate the blade pitch cable. Refer to
data on page 44 .
4. Put the blade pitch cable above the pulley and out
through the slot (E). (Fig. 27)
CAUTION:
blade pitch cable is in the groove of the
pulley and not on the outer side of the
pulley.
5. Put the handle in the handle holder and install the 2
bolts (C) and the 2 nuts (D). Tighten the nuts to 24
Nm/18 lb-ft. (Fig. 28)
6. Loosen the blade pitch cable: (Fig. 29)
a) For products with blade pitch knob (F), turn the
blade pitch knob fully counterclockwise.
b) For products with Pro-Shift
®
Pro-Shift
lever fully forward.
7. Put the blade pitch cable through the blade pitch
fork. (Fig. 30)
8. Attach the cable nut to the blade pitch cable.
9. Adjust the cable nut. The adjustment is correct when
the blade pitch cable is straight when the blades
have no pitch.
To install the throttle cable
1. Move the throttle control to the idle speed position.
(Fig. 31)
Introduction
WARNING:
safety chapter before you use the product.
To do before you operate the product
•
Read the operator's manual carefully and make sure
that you understand the instructions.
1452 - 002 - 20.05.2022
Assembly
Technical
Make sure that the
®
lever (G), push the
Operation
Read and understand the
2. Put the throttle cable through the clamp on the recoil
cover of the engine. (Fig. 32)
3. Put the bend of the throttle cable in the hole in the
throttle plate (A). (Fig. 33)
Note:
The air filter assembly can be removed to
get easier access.
4. Hold the throttle control in the idle speed position
while you put the bracket (B) on top of the throttle
cable.
5. Install the air filter assembly if it was removed.
To connect the wires from the handle to
the engine
1. Connect the wires (A) from the handle to the yellow
wires (B) from the engine. (Fig. 34)
2. Connect the green ground wire from the handle to
the green wire from the engine.
a) If the product has a green wire installed on the
engine, discard the green wire supplied with the
handle.
b) If the product does not have a green wire
installed on the engine, remove the nut (C),
install the ground wire and tighten the nut to 24
Nm/18 lb-ft. (Fig. 35)
To do a function check after assembly
1. Start the engine. Refer to
page 36 .
2. Do a check of the idle speed and the clutch. Refer to
Technical data on page 44 for the correct value.
a) Make sure that the blades do not rotate when the
engine is at idle speed.
b) Increase the engine speed and make sure that
the blades start to rotate.
3. Do a check of the gyroscopic safety switch. Refer
To do a check of the gyroscopic safety switch on
to
page 33 .
•
Read the engine manual that is supplied by the
engine manufacturer.
•
Do a check of the safety devices on the product.
Safety devices on the product on page 33 .
Refer to
•
Do the daily maintenance. Refer to
schedule on page 37 .
To adjust the handle height
•
Loosen the handle adjustment lever. Move the
handle up or down to an applicable height and
tighten the handle adjustment lever. (Fig. 36)
To start the product on
Maintenance
35
Werbung
Inhaltsverzeichnis
Fehlerbehebung
