Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
10
4. SETUP
4.1
Baby unit
Menu fl ow goes as follows for the baby unit once you push the menu button:
Channel & Sub-code > VOX Sensitivity > Auto Monitor > Exit menu
On the Baby unit, the following settings can be adjusted:
•
Send channel: this is the frequency at which the baby unit transmits. You can
choose from channel 1 ~ channel 8.
•
Sub code: this option adds an extra code to the signal allowing you to only listen
to your baby unit without interference from other transmitters on the same fre-
quency.
•
VOX: This allows you to determine how loud the baby must cry before the baby
units starts transmitting to the parent unit. At VOX setting 1 the baby must cry
loudly before the sound is transmitted to the parent unit. At VOX setting 4 also
(very) soft baby sounds are transmitted. It will require some experimenting to fi nd
your ideal VOX level.
•
Auto monitor: see chapter 5.3 of this manual for the description of this function.
1.
Insert the Baby unit into wall socket.
2.
Briefl y press the
3.
Briefl y press the
4.
Briefl y press the
sensitivity.
5.
Briefl y press the
'Auto Monitor' function.
6.
Briefl y press the
Note: When the nightlight of the baby unit is switched on, you CANNOT change the set-
When the nightlight of the baby unit is switched on, you CANNOT change the set-
When the nightlight of the baby unit is switched on, you CANNOT change the set-
tings. First press the
matically disappear from the screen if you do not press a button for a while.
4.2
Additional Baby Unit #2 or #3
Use a diff erent channel for each Baby unit when using 2 or 3 baby units. The other set-
tings can be freely adjusted.
4.3
Parent Unit
You set up the parent unit as follows:
1.
Briefl y press the ON/OFF key (10) button to enter the settings menu,
Briefl y press the ON/OFF key (10) button to enter the settings menu,
Briefl y press the ON/OFF key (10) button to enter the settings menu,
in the display (this means baby unit 1). Use the
baby unit 1 is present.
2.
Briefl y press the menu button (11) and choose to turn it ON or OFF by using the
Briefl y press the menu button (11) and choose to turn it ON or OFF by using the
or
as you have set for baby unit 1 by also using the
as you have set for baby unit 1 by also using the
3.
Briefl y press menu button (11) and use the
code as you have set for baby unit 1.
4.
Briefl y press menu button (11) to indicate whether baby unit 2 is present.
5.
Briefl y press the menu button (11) and choose to turn it ON or OFF by using the
Briefl y press the menu button (11) and choose to turn it ON or OFF by using the
or
button and then press menu shortly in order to set the same send channel as
button and then press menu shortly in order to set the same send channel as
button and then press menu shortly in order to set the same send channel as
you have set for baby unit 2 by also using the
you have set for baby unit 2 by also using the
6.
Briefl y press menu button (11) and use the
code as you have set for baby unit 2.
7.
Briefl y press menu button (11) again to indicate whether baby unit 3 is present.
button and use the
button and use the
button and use the
button and use the
button to save your settings and to fi nish the setup.
or
button to switch o the nightlight. The setup menu will auto-
button and then press menu briefl y in order to set the same send channel
button and then press menu briefl y in order to set the same send channel
button and then press menu briefl y in order to set the same send channel
or
button to set the send channel.
or
button to set the send sub code.
or
button to set the send the VOX
or
button to enable or disable the
or
button to indicate whether
or
button.
or
button to set the same sub
or
button.
or
button to set the same sub
1 appears
Werbung
Inhaltsverzeichnis
